Removing c500 fascia WITHOUT voiding warranty!, I've done it. It's fiddly, but possible. |
  |
 Feb 11 2006, 22:49
Post
#41
|
|||
|
Newbie  Group: Posters Posts: 4 Joined: 9th February 2006 Member No.: 171,896 Device(s): spv500  |
Ok. I had a go at this procedure (in an attempt to replace the front fascia on my C500) but I had to abandon the job halfway through. Fortunately, the reassembled phone still works fine after all the pulling and tugging (but I was very worried it wouldn't.)
When I tried to prise the fascia (black) from body (silver) of the phone, it was clear that the LCD screen was attached in some way to the back of the fascia. There was no way I could pull the fascia/body fully apart without damaging the connections between the LCD and the circuit board, especially with so little room to work in between a 'slightly separated' fascia and body. (BTW I've not had any problems with dust on the LCD which I guess is due to the seal & the attachment of the LCD to the fascia.) Is my only option now to send the phone to HTC for a proper repair job? Anyone know how they'll manage to separate the components safely when the LSD is attached to the fascia like this? Thanks Matt |
||
 |
 
|
||
|
Feb 11 2006, 23:06
Post
#42
|
|||
 Hardcore  Group: MoDaCo Plus Posts: 1,521 Joined: 22nd August 2005 Member No.: 145,647 Device(s): 8500 amongst others... |
QUOTE(matt14 @ Feb 11 2006, 23:49) When I tried to prise the fascia (black) from body (silver) of the phone, it was clear that the LCD screen was attached in some way to the back of the fascia. There was no way I could pull the fascia/body fully apart without damaging the connections between the LCD and the circuit board, especially with so little room to work in between a 'slightly separated' fascia and body. (BTW I've not had any problems with dust on the LCD which I guess is due to the seal & the attachment of the LCD to the fascia.) Is my only option now to send the phone to HTC for a proper repair job? Anyone know how they'll manage to separate the components safely when the LSD is attached to the fascia like this? Thanks Matt  The LCD isn't attached with anything stronger than double sided foam tape and wedged in, use a knife to prise the plastic edge free and the screen will come away. Richard -------------------- '....It's been out in Japan nearly 3 weeks - where's yours?'
|
||
|
|
|
||
|
Feb 13 2006, 10:30
Post
#43
|
|||
|
Regular  Group: Posters Posts: 98 Joined: 28th March 2005 Member No.: 120,062 Device(s): SPV C500 |
Yes, you do have to be carfuly not to break the connectors, thats why you should slide the credit card up the right side of the phone. Once thats dissconected I found the other side (which has the connecting ribbon) easy to get off - as far as I remember I just opened the facia like a door and the other side popped off.
|
||
|
|
|
||
|
Apr 2 2006, 21:18
Post
#44
|
||
|
Newbie Group: Posters Posts: 6 Joined: 13th March 2006 Member No.: 177,346 Device(s): SPV C600 |
Hi,
I Have the same dust problem but need to do it on a c600 (without voiding the warranty), Thanks. |
||
|
|
|
||
|
Apr 2 2006, 21:23
Post
#45
|
||
|
Newbie Group: Posters Posts: 6 Joined: 13th March 2006 Member No.: 177,346 Device(s): SPV C600 |
Hi,
I Need to do this but with a spv c600 (without voiding the warranty), Thanks. |
||
|
|
|
||
|
Apr 2 2006, 21:25
Post
#46
|
|||
|
Hardcore Group: MoDaCo Plus Posts: 1,521 Joined: 22nd August 2005 Member No.: 145,647 Device(s): 8500 amongst others... |
QUOTE(Benjc @ Apr 2 2006, 23:23) Hi, I Need to do this but with a spv c600 (without voiding the warranty), Thanks. Please don't cross post or double post. Might be better to continue in the topic you started: http://www.modaco.com/dust_behind_screen-t238205.html Richard -------------------- '....It's been out in Japan nearly 3 weeks - where's yours?'
|
||
|
|
|
||
|
Feb 27 2007, 04:46
Post
#47
|
||
|
Newbie Group: Posters Posts: 3 Joined: 5th August 2006 Member No.: 200,784 Device(s): Cingular 2125 |
QUOTE(fluffcat1 @ Apr 2 2006, 16:25) Please don't cross post or double post. Might be better to continue in the topic you started: http://www.modaco.com/dust_behind_screen-t238205.html Richard Has anyone here sucessfully done this with a Cingular 2125 (with the hump)? I have read these posts over and over and am having a very difficult time removing the antenna cover. I've got a bad scratch on the silver fascia or front of the phone and need to remove the back cover. I was planning on using some model paint to repaint the silver portion of the phone. The scratch is just at the point on the antenna hump where the silver part meets the antenna cover. I can get one side started, but it feels like something else is holding it in place. On my phone, the little opening just to the left of the battery connector is very small. I'm wondering if the antenna cover on the 2125 might be held in place differenty than models without the hump. I would like to buy a new complete housing for this phone, but can't seem to find one anywhere. I've seen Fluffcats's Ebay listing, but that housing wouldn't match up with my phone since it has the hump. I'm concerned about my reception if I were to remove that oversized antenna trying to fit it into a C600 housing. I called Cingular, who referred me to HTC who referred me back to Cingular. It looks like no one will sell parts for this phone. I had resigned myself to having to paint it, but I can't even get the antenna cover off. In the process of trying, I seemed to have done something to keep the antenna cover from closing back completely. Now it kind of sticks up on the left side. Any help would be appreciated. *I've attached a picture that shows those two openings. Notice how small the opening is to the left of the battery connector. I'm afraid I'm going to damage something trying to get that antenna cover off.
Attached File(s)
|
||
|
|
|
||
|
Jan 27 2008, 20:29
Post
#48
|
|||
|
Newbie Group: Posters Posts: 1 Joined: 30th May 2005 Member No.: 132,113 Device(s): spv 500 |
I know it's a long time since this post was started, and added to for that matter, but I just cleaned my c500 and its worked great!
many thanks! |
||
|
|
|
||
|
Similar Topics
| Topic | Replies | Topic Starter | Views | Last Action | |
|---|---|---|---|---|---|
 |
 Benq E72 UNBOXED! |
35 | Paul (MVP) | 8,347 | Today, 15:57 Last post by: 17-APG |
|
How to install and USE .net Compact Framework 3.5 WITHOUT upgrading your ROM. |
15 | Paul (MVP) | 22,142 | Today, 01:43 Last post by: wapvirus |
|
Samsung Omnia i900 now available on O2 FREE and with goodies! | 53 | Paul (MVP) | 6,410 | Today, 17:37 Last post by: Fiish |
|
The OFFICIAL Samsung i900 Omnia DXHH1 update: LEAKED! | 108 | Paul (MVP) | 5,630 | Today, 18:15 Last post by: landslot |
 |
Do I like it or not? I dunno! | 13 | Paul (MVP) | 204 | Today, 13:20 Last post by: steveoidm |
|
Need help fast!!! screen broken on my BJ II |
4 | H.Flores | 83 | Today, 15:19 Last post by: H.Flores |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
 |
Lo-Fi Version | Time is now: 5th September 2008 - 18:27 |
Please visit our 'Plus Partners' - these companies support MoDaCo through 'MoDaCo Plus' - Click Here for more details!
VITO Technology | Slipstream Solutions | Aiko Solutions | PDAMill | Inesoft | SBSH | LingvoSoft | Ruttensoft | Astraware | MadBeetle | Sprite Software
Opera | Westtek | TetraEdge | Z4Soft | KBM Systems | Conduits | Mini Lyrics Magic | Proporta | Semsons | SyncData | Active Kitten | Binaryfish | Textr
SPB Software House | Omega One | OmniSoft | Resco | eSoft Interactive | TenGo | ATEKsoft | imei-check | GpsGate | SplashData | DeveloperOne | monocube
WebIS, home of Pocket Informant, FlexMail and Note2Self
Would your company like to become a 'Plus Partner'? Click Here to contact us!
MoDaCo and Mobiholics are part of the MoDaCo.network, © Paul O'Brien 2002-2007. MoDaCo is managed by Upsolv, LLC.
Our Friends - CoolSmartphone - Smartphone Thoughts - MSMobileNews - MSMobiles - DSL Developments - Brodit Specialists - PDAhut. MoDaCo uses IntelliTxt technology.
Our Friends - CoolSmartphone - Smartphone Thoughts - MSMobileNews - MSMobiles - DSL Developments - Brodit Specialists - PDAhut. MoDaCo uses IntelliTxt technology.