Dissassembling HTC StrTrk / 8500 / S300/ F600 / SmartFlip

Send us News! | Rules

Please Log In or Register - it's FREE!

You Are Here » WinMo @ MoDaCo » Device Specific » HTC » STRTRk - STRTrk.MoDaCo.com

Dissassembling HTC StrTrk / 8500 / S300/ F600 / SmartFlip, without voiding warranty sticker. A bit tricky though.

Options

fluffcat1

Jul 22 2006, 02:50

Post #1

Hardcore

Group: MoDaCo Plus
Posts: 1,521
Joined: 22nd August 2005
Member No.: 145,647

Device(s): 8500 amongst others...

First, a note of caution. This is a *guide* you follow at your own risk. If you are in any way unsure, don't try it. If you've done a Typhoon or similar before, you'll have no problems.

THIS MAY VOID YOUR WARRANTY so only do it if you REALLY have to, for example you need to replace a smashed LCD or scuffed fascia. Remember kids, crying to HTC won't help if you can't get it back together again :cry:

I say 'may' as I was able to remove the warranty sticker intact and refit it afterwards. After cleaning my fingerprints off the inside.

You'll need a good torx T5, a small flat blade screwdriver, a sharp knife and a plastic tool to prise open the case. Try to work in a low-dust environment to minimise the risk of dust entering the screen area.

Ok. Take the battery cover off, sim out, battery out, mem card out and put to one side. Then, remove the rubber screen stop bungs from the top of the main screen by pushing them to one side with the plastic tool and then using the knife to grab the side edge of the bung and lever it up. This is the easiest way IMO as the sides don't get seen and they are stuck down firmly so won't just pull out. You could scrape them out with a screwdriver etc but you'll make them tatty so try a few different methods and find one that works for you.

HPIM0144.JPG ( 378.64K ) Number of downloads: 809

Use your T5 torx and remove the two screws revealed.

Turn over the phone. Take your 'case opening tool' and prise the edge of the rubberised endplate up at the front first and work it around either side to release the securing clips. The endplate will then hinge up like a car bonnet on the plastic locator guides on either side at the bottom of the plate. Disconnect the speaker wire and pull up and away from the phone. The media player button pushers will come away also but the buttons themselves are stuck to the LCD assembly.

HPIM0146.JPG ( 423.21K ) Number of downloads: 725

Interestingly the speaker is bi-directional as per the mpx200 - it is one assembly made of two speakers joined together facing away from each other, one as the earpiece and one as the loudspeaker. They share common earth and seperate signal wires.

HPIM0147.JPG ( 565.75K ) Number of downloads: 637

Next, remove the two small phillips screws from above the outer LCD that hold the metal plate in place. Take your case opening tool and lever up the edges of the metal plate, freeing the two clips either side, and elevate the front section of the metal plate. Whilst holding it away from the main phone, use the case opening tool to free the retaining clips at the base of the metal plate near the hinge. It is easier to do this with the hinge closed. Disconnect the backup battery ( I assume it's a backup battery alougth why does a WM5 device with persistant storage need a backup battery eh?) and lift clear.

HPIM0148.JPG ( 557.18K ) Number of downloads: 650

HPIM0149.JPG ( 591.06K ) Number of downloads: 653

Now remove the small philips from the base of the LCD surround, and using your case opening tool you can lever the LCD assembly from the phone frame carefully. Then disconnect the push-fit ribbon connector for the LCD from the board near the hinge, levering it up with your case opening tool gently to avoid damage. The main LCD is not fixed into it's metal frame other than through a connecting ribbon so be careful with it, and also watch for the LED notification section which is on the same ribbon assembly.

HPIM0152.JPG ( 381.23K ) Number of downloads: 546

The bad news is - the outer smaller LCD is part of the same ribbon assembly and not socketed - it is hard wired, unlike other makes of flip phone or flip - smartphone, which means a failure of either requires replacement of both. Annoying.

HPIM0154.JPG ( 450.13K ) Number of downloads: 509

Part number is 60H00053-00M in my unit. Manufacturer code is Toppolly TD022DHEA1

So we've got the top section in bits - now's the fun part :-)

Take your sharp knife along the left edge of the void sticker above the right hand screw. Run it up and down a few times to get under the sticker, then push the sticker to the right and off the side of the phone. Worked for me

HPIM0156.JPG ( 258.75K ) Number of downloads: 490

Remove the two torx screws. Take your case opening tool and prise up the edge near where the void sticker was. Hold it up and prise up the other side. Hold that and prise the metal figure of 8 clipe and 'L' shaped plastic clip in the battery compartment up.

HPIM0158.JPG ( 571.41K ) Number of downloads: 487

Still holding the two sides away from the body of the phone, work your case opening tool down to free another clip either side. Now here comes the REALLY fun part. The main case retaining mechanism at the bottom is a bit tricky. It has four clips near each other each facing away from the phone edge and in different directions to each other. Nice anti tamper mechanism. But I managed it. Use a twist / lift motion whilst working your case opening tool in that area to get the clips free without breaking. Take your time.

HPIM0159.JPG ( 586.91K ) Number of downloads: 712

Now unclip the keyboard ribbon, remove 2 philips screws and you can take out the mainboard. Isn't it diddy!

The keypad is stuck in and once removed will be difficult to get flat again so I left it alone but it would just push out if needed. The ribbon in the hinge looks easily replaceable if needed as well but I did not dissassemble that area.

Reassembly is the reverse of this procedure, just make sure to get the 'backup battery' lead seated well, and be careful locating the connectors at the hinge for the top metal plate. Then test everything, put your warranty sticker back on and no-one need ever know you had it in bits

Richard

This post has been edited by fluffcat1: Jul 22 2006, 05:15

--------------------

'....It's been out in Japan nearly 3 weeks - where's yours?'

gpcarreon (MVP)

Jul 22 2006, 02:56

Post #2

RN, MS MVP-MD
Group Icon

Group: Moderator Team
Posts: 4,536
Joined: 7th August 2003
From: Legazpi, Philippines
Member No.: 12,251

Device(s): ASUS P525, ASUS N10J-A1

Topic pinned. Thanks for the guide.

--------------------

Jakult everyday, everyday OK!

starclassic

Feb 28 2007, 04:56

Post #3

Newbie

Group: Posters
Posts: 11
Joined: 22nd January 2006
Member No.: 168,728

Device(s): Cingular 3125

Fantastic! This guide has been long awaited. Thanks, dude!

vvslavavv

May 2 2007, 23:43

Post #4

Newbie

Group: Posters
Posts: 1
Joined: 30th April 2007
Member No.: 251,698

Device(s): HTC 8500

Does anyone have any sources as to where I can order the replacement LCD screen?

Metzex08

Jul 1 2007, 04:50

Post #5

Newbie

Group: Posters
Posts: 1
Joined: 16th October 2006
Member No.: 210,394

Device(s): null

QUOTE(vvslavavv @ May 2 2007, 17:43)

Does anyone have any sources as to where I can order the replacement LCD screen?

I second this request. The only one i found was on ebay for $77. There is no way i am paying that for a tiny LCD. Thanks in advance!

sajlent

Jan 1 2008, 15:06

Post #6

Newbie

Group: Posters
Posts: 1
Joined: 26th February 2006
Member No.: 174,850

Device(s): Qtek 9100 & Qtek 8310

I know that a lot of time is past but maybe it can help in future:
http://mobile.brando.com.hk/prod_detail.php?prod_id=02923

Can anybody tell me where is vibra placed in this phone?

abatis

Dec 31 2008, 22:30

Post #7

Enthusiast
Group Icon

Group: MoDaCo Plus
Posts: 175
Joined: 23rd November 2003
Member No.: 21,802

I just used this guide to replace a broken screen on a Qtek from another Qtek that had a broken sycn connector but a good screen. Works great thanks. That little screw that holds the screen frame down is a bugger to put back in. I had to take and put a little dab of gum on my phillips head so I could insert it. I would never pass as a surgeon.

This post has been edited by abatis: Dec 31 2008, 22:31

« Next Oldest · STRTRk - STRTrk.MoDaCo.com · Next Newest »

Topic	Replies	Topic Starter	Views	Last Action
HTC Home (DARK/LIGHT/BLUE and NEW GUAVA!)	17	tho_	17,841	2nd July 2009 - 23:58 Last post by: n9rla
HTC Touch Pro2 availability roundup	9	Paul	1,349	2nd July 2009 - 13:03 Last post by: Rob.P
My htc/tachi style phone ex theme	2	shinta4e	200	2nd July 2009 - 01:28 Last post by: bga7x
HTC Magic Review - The HTC Google G2 Phone is Just Magic	0	sunshinewing	0	2nd July 2009 - 08:16 Last post by: sunshinewing
HTC Snap & Blackberry Connect Query into the HTC Snap being able to run Blackberry Connect	0	Atrum-Amicus	28	Yesterday, 11:25 Last post by: Atrum-Amicus
HTC Task Manager + SPB Mobile SHell 3 A Idea ?	0	Billou	105	Yesterday, 18:37 Last post by: Billou