TechnoLover

[KERNEL] TechnoLover's Kernel Edition 1.5 (25.06.2012)

762 posts in this topic

where do you look for battery bar? in notification bar or in settings?

lagfree reduces the frequency when the load is under a specific percentage, so maybe the load is at 368 MHz not low enough? When screen off, it should go down to 122 MHz ;)

i mean in the top bar, i didn't check in battery stats :) ok no problem about underclock, just to know ;)

today I'm gonna release new version I was too tired yesterday

will it be compatible with new 2.3.6 update?

Edited by chemicalbuz
0

Share this post


Link to post
Share on other sites

wifi not work in 2.3.6

0

Share this post


Link to post
Share on other sites

Kernel will be published 2-3 days later, because of stock 2.3.6, GignerOunay 3.0, new recovery and some bugs (:

0

Share this post


Link to post
Share on other sites

Kernel will be published 2-3 days later, because of stock 2.3.6, GignerOunay 3.0, new recovery and some bugs (:

I'm using your kernel with Gingerounay 3.0 without any question.:)

Wifi working as well.

Edited by stoorzsto
0

Share this post


Link to post
Share on other sites

Kernel will be published 2-3 days later, because of stock 2.3.6, GignerOunay 3.0, new recovery and some bugs (:

your Kernel working perfect,thanks,waiting for low voltage edition

Edited by mjpgly
0

Share this post


Link to post
Share on other sites

I'm using your kernel with Gingerounay 3.0 without any question.:)

Wifi working as well.

i tried flash this kernel with Gingerounay3.0,but can't boot......

i checked script,found app2sd script conflict with this kernel

Edited by mjpgly
0

Share this post


Link to post
Share on other sites

I am using this kernel with Gingerounay3.0. No issue except, phone get little warm.. and drain battery quite fast. Also seems charging is slower than usual.

Edited by mlk75
0

Share this post


Link to post
Share on other sites

Update (:

check first post (:

Edited by TechnoLover
0

Share this post


Link to post
Share on other sites

Thanks Techno. smile.gif

Can I ask what is stock Acer mV?

Is it 1100mV?

.

Edited by stonebear
0

Share this post


Link to post
Share on other sites

900/900/900/1050/1100/1200/1200/1250/1300/1350 - normally they should be displayed in MT Voltage Control app, because you shouldn't have any undervolt ;)

0

Share this post


Link to post
Share on other sites

900/900/900/1050/1100/1200/1200/1250/1300/1350 - normally they should be displayed in MT Voltage Control app, because you shouldn't have any undervolt ;)

So, if I select [email protected] (for example) that is stock, then I can choose lower mV and will be undervolting?

I then set mV for each individual frequency that the processor will use? 122, 245, 368 etc? Not like setting a maximum vcore and the OS decides vcore for all the frequencies based on that maximium.

.

Edited by stonebear
0

Share this post


Link to post
Share on other sites

yes, that's the way - be sure you test every frequency with chosen voltage.

yes, you can set voltage for every frequency. When you have done everything, you can save them for boot.

0

Share this post


Link to post
Share on other sites

yes, that's the way - be sure you test every frequency with chosen voltage.

yes, you can set voltage for every frequency. When you have done everything, you can save them for boot.

I understand now, thanks. smile.gif

0

Share this post


Link to post
Share on other sites

Update (:

check first post (:

It's awesome!

That's what I waiting for a looooong time --UV from OS-- Great work TechnoLover!

Thank You very much!

0

Share this post


Link to post
Share on other sites

Hi

I'm using dmd with the low voltage kernel. How do i know wich settings to make in the new kernel?

Are there presets?

Thanks

Torstiko

0

Share this post


Link to post
Share on other sites

No, there aren't any presets, I don't know the voltages from dmd, but you can have a view on my voltages on the first post, you see them on the screenshot. They are very low, so keep them a bit higher and try to lower them each for a bit ;)

0

Share this post


Link to post
Share on other sites

Thanks Technolover,

If i flash your kernel, are there still the current settings or the stock ones?

Greets

Torstiko

0

Share this post


Link to post
Share on other sites

After I saved my settings and do a reboot, at the first start, the program still shows the reference --stock-- voltages. Is it's just the app's starting value or it does a reading at start and the save was unsuccessful?

0

Share this post


Link to post
Share on other sites

please tell me your rom and I'll have a look ;)

yes it means it was unsuccessful in loading or saving them :/

Edited by TechnoLover
0

Share this post


Link to post
Share on other sites

please tell me your rom and I'll have a look ;)

yes it means it was unsuccessful in loading or saving them :/

I have same problem. After rebooting, MT Voltage Control shows stock value.

Official ROM 4.000.13 GEN1 with RecoveryMT 2.2, Root, your last kernel.

0

Share this post


Link to post
Share on other sites

i really like this kernel,so I flash new kernel on Gingerounay3.0,but apps2sd still can't work ,no /sd-ext

and some tweak lost,like /sys/devices/virtual/bdi/179:0/read_ahead_kb,Gingerounay3 is echo 1040

Edited by mjpgly
0

Share this post


Link to post
Share on other sites

I flash this new kernel on Gingerounay3.0,apps2sd still have problem,no /sd-ext

I don't think the kernel would affect that? Not that I know anything about this stuff. smile.gif

Edited by stonebear
0

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

MoDaCo is part of the MoDaCo.network, © Paul O'Brien 2002-2016. MoDaCo uses IntelliTxt technology.