45 replies to this topic

[vukodav]

Dengem, on 27 October 2011 - 02:30 AM, said:

and the voltage only usb Hub should do, or on the phone too??

USB standard requires 5V and 500mA per port. Iknow Racer charger doesn't have 5V and has 700mA power but it all worked. Phone was charging and USB hub working

[Dengem]

just at this the same cable and connect the mouse or do nothing except chargeproishidit, I installed the library. The reason?

[rpetya]

vukodav, on 26 October 2011 - 07:39 PM, said:

First, sorry for late answer. I used common 4 port USB hub, and Y type USB cable. Y USB cable I used has two A male and one mini  B plug. I plugged one A plug to phone charger (it provides power to phone and hub) and the other in OTG cable, mini B plug is for connecting hub.

As for your other question, you can't use Sven's kernel modules. Kernel modules have to be compiled along with kernel with which they are used. I didn't compile modules for USB VGA adapters because I don't have hardware to test them with

Thank you, I managed to connect and play with the mouse, but none of my flash drives is recognized. Since I do not have a proper hub, I drew power from the wall charger using a Y cable... This kernel is great!

[vukodav]

rpetya, on 27 October 2011 - 11:04 AM, said:

Thank you, I managed to connect and play with the mouse, but none of my flash drives is recognized. Since I do not have a proper hub, I drew power from the wall charger using a Y cable... This kernel is great!

thank you. I don't know why your flash drives don't work. Did you loaded kernel modules first?

[vukodav]

Dengem, on 27 October 2011 - 06:35 AM, said:

just at this the same cable and connect the mouse or do nothing except chargeproishidit, I installed the library. The reason?

I don't understand your question. Can you explain more about your problem?

[Dengem]

My firmware is # 224 on this board made ​​Ratserboy, your kernel.
I did otg cable (micro usb connector has closed the black wire and the mass) has connected the whole thing to a usb hub (power applied to the hub). But the mouse does not work only blinking LED on it, usb drives, too, did not give me any data. I beg to lay out a schematic diagram of the cable link to it! Thanks in advance, waiting for your answer ...

[rpetya]

vukodav, on 27 October 2011 - 10:27 PM, said:

thank you. I don't know why your flash drives don't work. Did you loaded kernel modules first?

yes, i did - without error messages... i tried to format the drive, but when i plug it in, its led flashes once and nothing gets mounted in /mnt...

[vukodav]

rpetya, on 29 October 2011 - 03:30 PM, said:

yes, i did - without error messages... i tried to format the drive, but when i plug it in, its led flashes once and nothing gets mounted in /mnt...

I don't know what seems to be the problem. I have only one flash drive, so I can't test kernel and modules more. And my phone ison repair sevice now, it had some hardware problems. When I get it back I'll test more and post results

[TigTex]

Nothing gets mounted on /mnt... that doesn't mean that the device is not recognized.

see if there is any /dev/hdx or /dev/sdx device before and after you plugin your flash drive.

(use "ls /dev | grep hd" and "ls /dev | grep sd")

dmesg log after you plug the flash drive can also be helpful (dmesg > /sdcard/dmesg.log)

Edited by TigTex, 13 November 2011 - 02:24 AM.

[kman12041]

What if uve got 2.3.7 nightlies and deadlinks dual touch kernal will that work.

Edited by kman12041, 13 November 2011 - 09:41 PM.

[rpetya]

TigTex, on 13 November 2011 - 02:23 AM, said:

Nothing gets mounted on /mnt... that doesn't mean that the device is not recognized.
see if there is any /dev/hdx or /dev/sdx device before and after you plugin your flash drive.
(use "ls /dev | grep hd" and "ls /dev | grep sd")
dmesg log after you plug the flash drive can also be helpful (dmesg > /sdcard/dmesg.log)

You are right, it gets recognized - at least that's what i decoded from dmesg output. However no hd or sd in /dev. Does it work for you TigTex?

Attached Files

•  dmesg.txt   6.41K   11 downloads

[TigTex]

Never tried it   Do you have all the modules in your phone? for example sd_mod.ko ... I have no idea what has been done on this kernel  

[euricoalex]

i need to type the commands again , if i switch off the phone or reboot ?

[euricoalex]

for me don't work with   ICS lookalike from racerboy . i make the cable (its easy to me i'm a Electronics Technician ) but d'ont detects anything . i need more information before change rom . can you help me . tanks

[kman12041]

It says not found should i worry or not

[kman12041]

Looks like theres a better usb host out.
Anyone got any ideas if itl work on our device.
http://forum.xda-dev...ad.php?t=480899

[kman12041]

I cant test it because it says you need active sync and for some reason it wont let me install it.
Can someone test it please

[euricoalex]

kman12041, on 04 December 2011 - 12:46 PM, said:

I cant test it because it says you need active sync and for some reason it wont let me install it.
Can someone test it please

It's for windows mobile . Do not work on android

[kman12041]

Yh i saw that when u said it but it said android so i got confused.
Says here
http://www.google.co...sb host android
First non ad result.

[rpetya]

Managed to get flash drive working, it had to be mounted manually:
#mount -t vfat /dev/block/sda1 /mnt/sdcard/usb-storage