Jump to content


Photo

Problems installing Jelly Bean ROM's

- - - - -

  • Please log in to reply
40 replies to this topic

#1
Fredriksen

Fredriksen

    Newbie

  • Members
  • Pip
  • 4 posts
  • Devices:ZTE Blade III
Hi,

For some reason my Blade III won't boot CM10 and CM10.1. I have been installing ROM's on all kinds of Android devices since the glory days of the G1 and never had any trouble before now.
Installing Aurora Borealis or Lewa works fine, but with both CM10 and CM10.1 the device shows the Cyanogenmod spinning logo and then freezes resulting in a boot loop.

Here is what I have tried so far:

- Wiping both before and after installation (factory reset, cache and dalwik) in all possible variations.
- Formatting system, data etc.
- I have checked MD5 checksums. All OK.
- Tried a different microSD card.

Any sugestions on what I can do next?

Thanks.

EDIT: Running Clockwork Recovery 6.0.2.7 btw.

EDIT2:

Made some progress. By entering recovery after boot loop and wiping dalwik and fixing permissions I get to the optimizing applications screen. Everytime it will freeze at some point during this time.

EDIT3: Went back to stock recovery and ROM (Swedish one) to start from scratch. Reinstalled CWM and tried to install CM10.1. Still the same problem. :(

Edited by Fredriksen, 16 April 2013 - 02:47 PM.

  • 1

#2
robt77

robt77

    Diehard

  • Members
  • PipPipPipPip
  • 343 posts
  • Gender:Male
  • Location:Salford
  • Devices:ZTE Blade III
Strange, if you can grab a log cat from ADB when you are in the boot loop it might shed some light on why it is not booting properly, apart from that the only thing you could do is try the download again and start again.

  • 1

#3
robt77

robt77

    Diehard

  • Members
  • PipPipPipPip
  • 343 posts
  • Gender:Male
  • Location:Salford
  • Devices:ZTE Blade III
Strange, if you can grab a log cat from ADB when you are in the boot loop it might shed some light on why it is not booting properly, apart from that the only thing you could do is try the download again and start again.

  • 1

#4
Fredriksen

Fredriksen

    Newbie

  • Members
  • Pip
  • 4 posts
  • Devices:ZTE Blade III
Thanks for the reply.

I have tried redownloading a few times and installed different CM10-based ROM's and it's the same with all of them. ICS-based ROM's installs with no problem at all.

I will try to get a log cat and post it here.

  • 0

#5
Fredriksen

Fredriksen

    Newbie

  • Members
  • Pip
  • 4 posts
  • Devices:ZTE Blade III
Here is a logcat. Here it doesn't even reach the Cyanogenmod boot animation:


- waiting for device -
--------- beginning of /dev/log/main
I/installd( 113): installd firing up
I/DEBUG ( 107): debuggerd: Mar 29 2013 18:35:04
--------- beginning of /dev/log/system
I/Vold ( 104): Vold 2.1 (the revenge) firing up
E/rmt_storage( 120): rmt_storage force sync
E/rmt_storage( 120): rmt_storage rmt_force_sync : [MyTag]open: fd=12
E/AKMD2 ( 115): compass layout file is not existed!!
D/Vold ( 104): Volume sdcard state changing -1 (Initializing) -> 0 (No-Media
)
I/Netd ( 106): Netd 1.0 starting
W/InterfaceController( 106): Warning (Cannot load library: load_library(linker.
cpp:771): library "/system/lib/libnetcmdiface.so" not found) while opening the n
et interface command library
W/libc ( 118): WARNING: generic atexit() called from legacy shared library
D/Vold ( 104): Volume sdcard state changing 0 (No-Media) -> 2 (Pending)
D/DirectVolume( 104): DirectVolume::handlePartitionAdded -> MAJOR 179, MINOR 33
, PARTN 1
D/Vold ( 104): Volume sdcard state changing 2 (Pending) -> 1 (Idle-Unmounted
)
I/cm ( 146): ____ _ _ ____ _ _ ____ ____ ____ _ _ _ _ ____ ___
I/cm ( 147): | \_/ |__| |\ | | | | __ |___ |\ | |\/| | | | \
I/SurfaceFlinger( 109): SurfaceFlinger is starting
I/SurfaceFlinger( 109): use dithering
I/cm ( 148): |___ | | | | \| |__| |__] |___ | \| | | |__| |__/
E/rmt_storage( 120): block rmt_storage client thread
I/SurfaceFlinger( 109): SurfaceFlinger's main thread ready to run. Initializing
graphics H/W...
D/libEGL ( 109): loaded /system/lib/egl/libEGL_adreno200.so
D/libEGL ( 109): loaded /system/lib/egl/libGLESv1_CM_adreno200.so
I/cm ( 169): Welcome to Android 4.2.2 / CyanogenMod-10.1-20130329-KonstaKA
NG-atlas40
D/libEGL ( 109): loaded /system/lib/egl/libGLESv2_adreno200.so
D/AndroidRuntime( 110):
D/AndroidRuntime( 110): >>>>>> AndroidRuntime START com.android.internal.os.Zyg
oteInit <<<<<<
D/AndroidRuntime( 110): CheckJNI is OFF
I/mediaserver( 112): ServiceManager: 0x40cc4f90
I/AudioFlinger( 112): Using default 3000 mSec as standby time.
E/MediaPlayerFactory( 112): Failed to open FACTORY_LIB Error : Cannot load libr
ary: load_library(linker.cpp:771): library "libdashplayer.so" not found
I/CameraService( 112): CameraService started (pid=112)
E/QualcommCamera( 112): Qint android::get_number_of_cameras(): E
I/QualcommCameraHardware( 112): getCameraInfo: IN
I/QualcommCameraHardware( 112): getCameraInfo: loading libqcamera at 0x40019ed8

V/QualcommCameraHardware( 112): Storing the current target type as 3
I/QualcommCameraHardware( 112): getCameraInfo: numOfCameras = 1
I/QualcommCameraHardware( 112): Camera sensor 0 info:
I/QualcommCameraHardware( 112): camera_id: 0
I/QualcommCameraHardware( 112): modes_supported: 5
I/QualcommCameraHardware( 112): position: 0
I/QualcommCameraHardware( 112): sensor_mount_angle: 0
V/QualcommCameraHardware( 112): getCameraInfo: dlclose(libqcamera)
I/QualcommCameraHardware( 112): getCameraInfo: OUT
I/AudioPolicyManagerBase( 112): loadAudioPolicyConfig() loaded /system/etc/audi
o_policy.conf
I/AudioHardwareMSM76XXA( 112): get_audpp_filter
I/AudioHardwareMSM76XXA( 112): open /system/etc/AudioFilter.csv success.
I/AudioHardwareMSM76XXA( 112): EQ flag = 00.
I/AudioHardwareMSM76XXA( 112): EQ flag = 00.
I/AudioHardwareMSM76XXA( 112): EQ flag = 00.
E/AudioHardwareMSM76XXA( 112): failed to open AUTO_VOLUME_CONTROL /system/etc/A
utoVolumeControl.txt: No such file or directory (2)
D/AudioHardwareMSM76XXA( 112): Auto Volume Enabled= 0
I/AudioHardwareMSM76XXA( 112): Set master volume to 7.
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(0, 0, 7)
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(6, 0, 7)
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(12, 0, 7)
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(3, 0, 7)
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(16, 0, 7)
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(25, 0, 7)
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(8, 0, 1)
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(9, 0, 1)
I/AudioFlinger( 112): loadHwModule() Loaded primary audio interface from QCOM A
udio HW HAL (audio) handle 1
I/AudioFlinger( 112): HAL output buffer size 1200 frames, normal mix buffer siz
e 1200 frames
I/AudioMixer( 112): found effect "Multichannel Downmix To Stereo" from The Andr
oid Open Source Project
I/AudioFlinger( 112): Using module 1 has the primary audio interface
D/AudioHardwareInterface( 112): setMode(NORMAL)
I/AudioFlinger( 112): AudioFlinger's thread 0x40138008 ready to run
W/AudioFlinger( 112): Thread AudioOut_2 cannot connect to the power manager ser
vice
I/AudioHardwareMSM76XXA( 112): Routing audio to Speakerphone
W/AudioHardwareMSM76XXA( 112): rpc_snd_set_device(6, 1, 1)
D/AudioHardwareMSM76XXA( 112): setVoiceVolume(0.400000)
I/AudioHardwareMSM76XXA( 112): Setting in-call volume to 2 (available range is
2 to 7)
D/AudioHardwareMSM76XXA( 112): rpc_snd_set_volume(38, 0, 2)
I/audio_a2dp_hw( 112): adev_open: adev_open in A2dp_hw module
I/AudioFlinger( 112): loadHwModule() Loaded a2dp audio interface from A2DP Audi
o HW HAL (audio) handle 3
I/AudioPolicyService( 112): Loaded audio policy from QCOM Audio Policy HAL (aud
io_policy)
E/ ( 108): cby, conn_id = 1, client_id = 1, service_id = 11
E/ ( 108): cby, conn_id = 1, client_id = 1, service_id = 10
W/gralloc ( 109): MSMFB_METADATA_SET failed to configure alpha mode
I/gralloc ( 109): using (fd=15)
I/gralloc ( 109): id = msmfb30_80201
I/gralloc ( 109): xres = 480 px
I/gralloc ( 109): yres = 800 px
I/gralloc ( 109): xres_virtual = 480 px
I/gralloc ( 109): yres_virtual = 2400 px
I/gralloc ( 109): bpp = 32
I/gralloc ( 109): r = 24:8
I/gralloc ( 109): g = 16:8
I/gralloc ( 109): b = 8:8
I/gralloc ( 109): width = 76 mm (160.421051 dpi)
I/gralloc ( 109): height = 127 mm (160.000000 dpi)
I/gralloc ( 109): refresh rate = 60.00 Hz
D/CALCFPS ( 109): DEBUG_CALC_FPS: 0
D/CALCFPS ( 109): period: 10
D/CALCFPS ( 109): ignorethresh_us: 500000
D/CALCFPS ( 109): DEBUG_CALC_FPS: 0
D/CALCFPS ( 109): period: 10
D/CALCFPS ( 109): ignorethresh_us: 500000
F/libc ( 338): Fatal signal 11 (SIGSEGV) at 0x000520b8 (code=1), thread 338
(ip)

  • 0

#6
BladeIII

BladeIII

    Newbie

  • Members
  • Pip
  • 8 posts
  • Devices:Zte BladeIII

Hi,

For some reason my Blade III won't boot CM10 and CM10.1. I have been installing ROM's on all kinds of Android devices since the glory days of the G1 and never had any trouble before now.
Installing Aurora Borealis or Lewa works fine, but with both CM10 and CM10.1 the device shows the Cyanogenmod spinning logo and then freezes resulting in a boot loop.

Here is what I have tried so far:

- Wiping both before and after installation (factory reset, cache and dalwik) in all possible variations.
- Formatting system, data etc.
- I have checked MD5 checksums. All OK.
- Tried a different microSD card.

Any sugestions on what I can do next?

Thanks.

EDIT: Running Clockwork Recovery 6.0.2.7 btw.

EDIT2:

Made some progress. By entering recovery after boot loop and wiping dalwik and fixing permissions I get to the optimizing applications screen. Everytime it will freeze at some point during this time.

EDIT3: Went back to stock recovery and ROM (Swedish one) to start from scratch. Reinstalled CWM and tried to install CM10.1. Still the same problem. :(


What Lewa os? give me a link please.. :D

  • 0

#7
Fredriksen

Fredriksen

    Newbie

  • Members
  • Pip
  • 4 posts
  • Devices:ZTE Blade III

  • 0

#8
capoeirabg

capoeirabg

    Newbie

  • Members
  • Pip
  • 2 posts
  • Devices:null
I too have this problem.
And after almost an hour latter and 11 reboots it has been installed but it freezes at random points while using it.
I also tried formating every partition that CWM can and no change at all.

The same thing happens if i tried to install 4.1.2 ROM also.

Edited by capoeirabg, 22 April 2013 - 09:15 AM.

  • 0

#9
capoeirabg

capoeirabg

    Newbie

  • Members
  • Pip
  • 2 posts
  • Devices:null
After several attempts i manage to record several Log-s.
after formating every partition except external-sd, i aways get to this error in process 109 - D/AndroidRuntime( 109): >>>>>> AndroidRuntime START com.android.internal.os.ZygoteInit <<<<<<
All the error are from just this type:
Unable to open or create cache for /system/framework/****

It all starts after this:


W/dalvikvm( 377): msync failed: Read-only file system
E/dalvikvm( 377): DexOpt dep info: write failed: Read-only file system
W/dalvikvm( 377): Failed writing dependencies
E/dalvikvm( 377): Optimization failed
W/dalvikvm( 109): DexOpt: --- END 'core.jar' --- status=0xff00, process failed
E/dalvikvm( 109): Unable to extract+optimize DEX from '/system/framework/core.jar'
D/dalvikvm( 109): Unable to process classpath element '/system/framework/core.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache

And when actual install starts here is the state of all mounted partitions:
1|shell@android:/ $ mount
mount
rootfs / rootfs ro,relatime 0 0
tmpfs /dev tmpfs rw,nosuid,relatime,mode=755 0 0
devpts /dev/pts devpts rw,relatime,mode=600 0 0
proc /proc proc rw,relatime 0 0
sysfs /sys sysfs rw,relatime 0 0
tmpfs /storage tmpfs rw,relatime,mode=050,gid=1028 0 0
debugfs /sys/kernel/debug debugfs rw,relatime 0 0
none /acct cgroup rw,relatime,cpuacct 0 0
tmpfs /mnt/secure tmpfs rw,relatime,mode=700 0 0
tmpfs /mnt/asec tmpfs rw,relatime,mode=755,gid=1000 0 0
tmpfs /mnt/obb tmpfs rw,relatime,mode=755,gid=1000 0 0
tmpfs /mnt/fuse tmpfs rw,relatime,mode=775,gid=1000 0 0
none /dev/cpuctl cgroup rw,relatime,cpu 0 0
/dev/block/mmcblk0p19 /system ext4 ro,relatime,user_xattr,barrier=1,data=ordered 0 0
/dev/block/mmcblk0p21 /cache ext4 rw,nosuid,nodev,relatime,user_xattr,barrier=1,data=ordered 0 0
/dev/block/mmcblk0p22 /data ext4 rw,nosuid,nodev,relatime,user_xattr,barrier=1,data=ordered,noauto_da_alloc 0 0
/dev/fuse /mnt/shell/emulated fuse rw,nosuid,nodev,relatime,user_id=1023,group_id=1023,default_permissions,allow_other 0
0
I think that the /system partition have to be RW at this point, so it almost certain a permission error.
Will be glad if some one would point me to direction how to remount system in RW while Installing clockwork

Here is the actual log:
C:\Users\capoeira\Desktop\adt-bundle-windows-x86-20130219\adt-bundle-windows-x86-20130219\sdk\platform-tools>adb.exe log
cat
- waiting for device -
--------- beginning of /dev/log/main
I/installd( 112): installd firing up
E/cutils ( 112): Failed to read /data/.layout_version: No such file or directory
I/DEBUG ( 106): debuggerd: Apr 18 2013 11:20:23
E/AKMD2 ( 114): compass layout file is not existed!!
D/installd( 112): Upgrading /data/media for multi-user
D/installd( 112): Upgrading to shared /data/media/obb
E/rmt_storage( 120): rmt_storage force sync
E/rmt_storage( 120): rmt_storage rmt_force_sync : [MyTag]open: fd=12
I/cm	 ( 137): ____ _ _ ____ _ _ ____ ____ ____ _ _ _ _ ____ ___
W/libc ( 117): WARNING: generic atexit() called from legacy shared library
I/cm	 ( 139): |	 \_/ |__| |\ | | | | __ |___ |\ | |\/| | | | \
I/cm	 ( 142): |___ | | | | \| |__| |__] |___ | \| | | |__| |__/
--------- beginning of /dev/log/system
I/Vold ( 103): Vold 2.1 (the revenge) firing up
D/Vold ( 103): Volume sdcard state changing -1 (Initializing) -> 0 (No-Media)
I/Netd ( 105): Netd 1.0 starting
W/InterfaceController( 105): Warning (Cannot load library: load_library(linker.cpp:771): library "/system/lib/libnetcmd
iface.so" not found) while opening the net interface command library
E/rmt_storage( 120): block rmt_storage client thread
D/Vold ( 103): Volume sdcard state changing 0 (No-Media) -> 2 (Pending)
I/SurfaceFlinger( 108): SurfaceFlinger is starting
I/SurfaceFlinger( 108): use dithering
D/DirectVolume( 103): DirectVolume::handlePartitionAdded -> MAJOR 179, MINOR 33, PARTN 1
D/Vold ( 103): Volume sdcard state changing 2 (Pending) -> 1 (Idle-Unmounted)
I/SurfaceFlinger( 108): SurfaceFlinger's main thread ready to run. Initializing graphics H/W...
D/libEGL ( 108): loaded /system/lib/egl/libEGL_adreno200.so
D/libEGL ( 108): loaded /system/lib/egl/libGLESv1_CM_adreno200.so
I/cm	 ( 165): Welcome to Android 4.2.2 / CyanogenMod-10.1-20130418-KonstaKANG-atlas40
D/libEGL ( 108): loaded /system/lib/egl/libGLESv2_adreno200.so
I/Adreno200-EGL( 108): <qeglDrvAPI_eglInitialize:290>: EGL 1.4 QUALCOMM build: AU_LINUX_ANDROID_JB.04.01.01.00.005_msm7
627a_JB_CL2577695_release_AU (CL2577695)
I/Adreno200-EGL( 108): Build Date: 07/11/12 Wed
I/Adreno200-EGL( 108): Local Branch: mybranch65565
I/Adreno200-EGL( 108): Remote Branch: quic/master
I/Adreno200-EGL( 108): Local Patches: NONE
I/Adreno200-EGL( 108): Reconstruct Branch: AU_LINUX_ANDROID_JB.04.01.01.00.005 + db7e81a + 4568683 + dfff884 + NOTHING
W/gralloc ( 108): MSMFB_METADATA_SET failed to configure alpha mode
I/gralloc ( 108): using (fd=19)
I/gralloc ( 108): id		 = msmfb30_80201
I/gralloc ( 108): xres		 = 480 px
I/gralloc ( 108): yres		 = 800 px
I/gralloc ( 108): xres_virtual = 480 px
I/gralloc ( 108): yres_virtual = 2400 px
I/gralloc ( 108): bpp		 = 32
I/gralloc ( 108): r		 = 24:8
I/gralloc ( 108): g		 = 16:8
I/gralloc ( 108): b		 = 8:8
I/gralloc ( 108): width	 = 76 mm (160.421051 dpi)
I/gralloc ( 108): height	 = 127 mm (160.000000 dpi)
I/gralloc ( 108): refresh rate = 60.00 Hz
D/CALCFPS ( 108): DEBUG_CALC_FPS: 0
D/CALCFPS ( 108): period: 10
D/CALCFPS ( 108): ignorethresh_us: 500000
D/CALCFPS ( 108): DEBUG_CALC_FPS: 0
D/CALCFPS ( 108): period: 10
D/CALCFPS ( 108): ignorethresh_us: 500000
I/hwcomposer( 108): Initializing Qualcomm Hardware Composer
I/hwcomposer( 108): MDP version: 300
I/hwcomposer( 108): DYN composition threshold : 2.000000
I/SurfaceFlinger( 108): Using composer version 1.0
I/hwcomposer( 108): Initializing UEvent Listener Thread
I/hwcomposer( 108): Initializing VSYNC Thread
W/SurfaceFlinger( 108): getting VSYNC period from fb HAL: 16666666
W/Adreno200-EGL( 108): <qeglDrvAPI_eglChooseConfig:774>: EGL_BAD_ATTRIBUTE
W/SurfaceFlinger( 108): no suitable EGLConfig found, trying without EGL_FRAMEBUFFER_TARGET_ANDROID
W/SurfaceFlinger( 108): no suitable EGLConfig found, trying without EGL_RECORDABLE_ANDROID
E/Trace ( 108): error opening trace file: No such file or directory (2)
I/SurfaceFlinger( 108): EGL informations:
I/SurfaceFlinger( 108): vendor : Android
I/SurfaceFlinger( 108): version : 1.4 Android META-EGL
I/SurfaceFlinger( 108): extensions: EGL_KHR_image EGL_KHR_image_base EGL_KHR_gl_texture_2D_image EGL_KHR_gl_texture_cub
emap_image EGL_KHR_gl_renderbuffer_image EGL_KHR_fence_sync EGL_ANDROID_image_native_buffer
I/SurfaceFlinger( 108): Client API: OpenGL_ES
I/SurfaceFlinger( 108): EGLSurface: 8-8-8-8, config=0x4
I/SurfaceFlinger( 108): OpenGL ES informations:
I/SurfaceFlinger( 108): vendor : Qualcomm
I/SurfaceFlinger( 108): renderer : Adreno (TM) 200
I/SurfaceFlinger( 108): version : OpenGL ES-CM 1.1
I/SurfaceFlinger( 108): extensions: GL_EXT_debug_marker GL_AMD_compressed_ATC_texture GL_AMD_performance_monitor GL_APP
LE_texture_2D_limited_npot GL_ARB_vertex_buffer_object GL_EXT_texture_filter_anisotropic GL_EXT_texture_format_BGRA8888
GL_EXT_texture_type_2_10_10_10_REV GL_OES_blend_equation_separate GL_OES_blend_func_separate GL_OES_blend_subtract GL_OE
S_compressed_ETC1_RGB8_texture GL_OES_compressed_paletted_texture GL_OES_depth_texture GL_OES_depth24 GL_OES_draw_textur
e GL_OES_EGL_image GL_OES_EGL_image_external GL_OES_framebuffer_object GL_OES_matrix_palette GL_OES_packed_depth_stencil
GL_OES_point_size_array GL_OES_point_sprite GL_OES_read_format GL_OES_rgb8_rgba8 GL_OES_stencil_wrap GL_OES_texture_cub
e_map GL_OES_texture_env_crossbar GL_OES_texture_float GL_OES_texture_half_float GL_OES_texture_half_float_linear GL_OES
_texture_npot GL_OES_texture_mirrored_repeat GL_QCOM_binning_control GL_QCOM_extended_get GL_QCOM_tiled_rendering GL_AMD
_compressed_3DC_texture
I/SurfaceFlinger( 108): GL_MAX_TEXTURE_SIZE = 4096
I/SurfaceFlinger( 108): GL_MAX_VIEWPORT_DIMS = 4096 x 4096
D/SurfaceFlinger( 108): Screen acquired, type=0 flinger=0x4143d318
D/libEGL ( 218): loaded /system/lib/egl/libEGL_adreno200.so
D/libEGL ( 218): loaded /system/lib/egl/libGLESv1_CM_adreno200.so
D/libEGL ( 218): loaded /system/lib/egl/libGLESv2_adreno200.so
I/Adreno200-EGL( 218): <qeglDrvAPI_eglInitialize:290>: EGL 1.4 QUALCOMM build: AU_LINUX_ANDROID_JB.04.01.01.00.005_msm7
627a_JB_CL2577695_release_AU (CL2577695)
I/Adreno200-EGL( 218): Build Date: 07/11/12 Wed
I/Adreno200-EGL( 218): Local Branch: mybranch65565
I/Adreno200-EGL( 218): Remote Branch: quic/master
I/Adreno200-EGL( 218): Local Patches: NONE
I/Adreno200-EGL( 218): Reconstruct Branch: AU_LINUX_ANDROID_JB.04.01.01.00.005 + db7e81a + 4568683 + dfff884 + NOTHING
E/Trace ( 218): error opening trace file: No such file or directory (2)
D/memalloc( 108): init_pmem_area: Initializing pmem area
D/memalloc( 108): init_pmem_area_locked: Opening master pmem FD
D/memalloc( 108): init_pmem_area_locked: Total pmem size: 27262976
D/AndroidRuntime( 109):
D/AndroidRuntime( 109): >>>>>> AndroidRuntime START com.android.internal.os.ZygoteInit <<<<<<
D/AndroidRuntime( 109): CheckJNI is OFF
I/mediaserver( 111): ServiceManager: 0x40a32ed8
I/AudioFlinger( 111): Using default 3000 mSec as standby time.
I/CameraService( 111): CameraService started (pid=111)
E/QualcommCamera( 111): Qint android::get_number_of_cameras(): E
I/QualcommCameraHardware( 111): getCameraInfo: IN
I/QualcommCameraHardware( 111): getCameraInfo: loading libqcamera at 0x40028ed8
V/QualcommCameraHardware( 111): Storing the current target type as 3
I/QualcommCameraHardware( 111): getCameraInfo: numOfCameras = 1
I/QualcommCameraHardware( 111): Camera sensor 0 info:
I/QualcommCameraHardware( 111): camera_id: 0
I/QualcommCameraHardware( 111): modes_supported: 5
I/QualcommCameraHardware( 111): position: 0
I/QualcommCameraHardware( 111): sensor_mount_angle: 0
V/QualcommCameraHardware( 111): getCameraInfo: dlclose(libqcamera)
I/QualcommCameraHardware( 111): getCameraInfo: OUT
I/AudioPolicyManagerBase( 111): loadAudioPolicyConfig() loaded /system/etc/audio_policy.conf
I/AudioHardwareMSM76XXA( 111): get_audpp_filter
I/AudioHardwareMSM76XXA( 111): open /system/etc/AudioFilter.csv success.
I/AudioHardwareMSM76XXA( 111): EQ flag = 00.
I/AudioHardwareMSM76XXA( 111): EQ flag = 00.
I/AudioHardwareMSM76XXA( 111): EQ flag = 00.
E/AudioHardwareMSM76XXA( 111): failed to open AUTO_VOLUME_CONTROL /system/etc/AutoVolumeControl.txt: No such file or di
rectory (2)
D/AudioHardwareMSM76XXA( 111): Auto Volume Enabled= 0
I/AudioHardwareMSM76XXA( 111): Set master volume to 7.
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(0, 0, 7)
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(6, 0, 7)
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(12, 0, 7)
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(3, 0, 7)
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(16, 0, 7)
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(25, 0, 7)
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(8, 0, 1)
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(9, 0, 1)
I/AudioFlinger( 111): loadHwModule() Loaded primary audio interface from QCOM Audio HW HAL (audio) handle 1
I/AudioFlinger( 111): HAL output buffer size 1200 frames, normal mix buffer size 1200 frames
I/AudioMixer( 111): found effect "Multichannel Downmix To Stereo" from The Android Open Source Project
I/AudioFlinger( 111): Using module 1 has the primary audio interface
D/AudioHardwareInterface( 111): setMode(NORMAL)
I/AudioFlinger( 111): AudioFlinger's thread 0x40061008 ready to run
W/AudioFlinger( 111): Thread AudioOut_2 cannot connect to the power manager service
E/	 ( 107): cby, conn_id = 1, client_id = 1, service_id = 11
I/AudioHardwareMSM76XXA( 111): Routing audio to Speakerphone
W/AudioHardwareMSM76XXA( 111): rpc_snd_set_device(6, 1, 1)
D/AudioHardwareMSM76XXA( 111): setVoiceVolume(0.400000)
I/AudioHardwareMSM76XXA( 111): Setting in-call volume to 2 (available range is 2 to 7)
D/AudioHardwareMSM76XXA( 111): rpc_snd_set_volume(38, 0, 2)
E/	 ( 107): cby, conn_id = 1, client_id = 1, service_id = 10
I/audio_a2dp_hw( 111): adev_open: adev_open in A2dp_hw module
I/AudioFlinger( 111): loadHwModule() Loaded a2dp audio interface from A2DP Audio HW HAL (audio) handle 3
I/AudioPolicyService( 111): Loaded audio policy from QCOM Audio Policy HAL (audio_policy)
E/rmt_storage( 120): write_log_file: [MyTag]open: fd=-1
E/rmt_storage( 120): block rmt_storage client thread
D/dalvikvm( 109): DexOpt: --- BEGIN 'core.jar' (bootstrap=1) ---
D/MDnsDS ( 105): MDnsSdListener::Hander starting up
D/MDnsDS ( 105): MDnsSdListener starting to monitor
D/MDnsDS ( 105): Going to poll with pollCount 1
D/dalvikvm( 377): Ignoring duplicate verify attempt on Ljava/lang/Object;
D/dalvikvm( 377): Ignoring duplicate verify attempt on Ljava/lang/Class;
D/dalvikvm( 377): Ignoring duplicate verify attempt on Ljava/lang/ref/Reference;
D/dalvikvm( 377): Ignoring duplicate verify attempt on Ljava/lang/ref/ReferenceQueue;
D/dalvikvm( 377): Ignoring duplicate verify attempt on Ljava/lang/ref/FinalizerReference;
D/dalvikvm( 377): DexOpt: load 160ms, verify+opt 2188ms, 1615612 bytes
W/dalvikvm( 377): msync failed: Read-only file system
E/dalvikvm( 377): DexOpt dep info: write failed: Read-only file system
W/dalvikvm( 377): Failed writing dependencies
E/dalvikvm( 377): Optimization failed
W/dalvikvm( 109): DexOpt: --- END 'core.jar' --- status=0xff00, process failed
E/dalvikvm( 109): Unable to extract+optimize DEX from '/system/framework/core.jar'
D/dalvikvm( 109): Unable to process classpath element '/system/framework/core.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/core-junit.jar (/data/dalvik-cache/system@framew
[email protected]@classes.dex)
D/dalvikvm( 109): Unable to process classpath element '/system/framework/core-junit.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/bouncycastle.jar (/data/dalvik-cache/system@fram
[email protected]@classes.dex)
D/dalvikvm( 109): Unable to process classpath element '/system/framework/bouncycastle.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/ext.jar (/data/dalvik-cache/system@framework@ext
.[email protected])
D/dalvikvm( 109): Unable to process classpath element '/system/framework/ext.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/framework.jar (/data/dalvik-cache/system@framewo
[email protected]@classes.dex)
D/dalvikvm( 109): Unable to process classpath element '/system/framework/framework.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/telephony-common.jar (/data/dalvik-cache/system@
[email protected]@classes.dex)
D/dalvikvm( 109): Unable to process classpath element '/system/framework/telephony-common.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/mms-common.jar (/data/dalvik-cache/system@framew
[email protected]@classes.dex)
D/dalvikvm( 109): Unable to process classpath element '/system/framework/mms-common.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/android.policy.jar (/data/dalvik-cache/system@fr
[email protected]@classes.dex)
D/dalvikvm( 109): Unable to process classpath element '/system/framework/android.policy.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/services.jar (/data/dalvik-cache/system@framewor
[email protected]@classes.dex)
D/dalvikvm( 109): Unable to process classpath element '/system/framework/services.jar'
E/dalvikvm( 109): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 109): Unable to open or create cache for /system/framework/apache-xml.jar (/data/dalvik-cache/system@framew
[email protected]@classes.dex)
D/dalvikvm( 109): Unable to process classpath element '/system/framework/apache-xml.jar'
E/dalvikvm( 109): No valid entries found in bootclasspath '/system/framework/core.jar:/system/framework/core-junit.jar:
/system/framework/bouncycastle.jar:/system/framework/ext.jar:/system/framework/framework.jar:/system/framework/telephony
-common.jar:/system/framework/mms-common.jar:/system/framework/android.policy.jar:/system/framework/services.jar:/system
/framework/apache-xml.jar'
E/dalvikvm( 109): VM aborting
F/libc ( 109): Fatal signal 11 (SIGSEGV) at 0xdeadd00d (code=1), thread 109 (zygote)
W/libc ( 117): WARNING: generic atexit() called from legacy shared library
I/DEBUG ( 106): failed to open tombstone file '/data/tombstones/tombstone_00': No such file or directory
I/Netd ( 442): Netd 1.0 starting
I/ServiceManager( 102): service 'media.camera' died
I/ServiceManager( 102): service 'media.audio_policy' died
I/ServiceManager( 102): service 'media.audio_flinger' died
I/ServiceManager( 102): service 'media.player' died
W/InterfaceController( 442): Warning (Cannot load library: load_library(linker.cpp:771): library "/system/lib/libnetcmd
iface.so" not found) while opening the net interface command library
E/	 ( 117): cby, conn_id = 0, client_id = 1, service_id = 1
E/	 ( 117): cby, conn_id = 1, client_id = 1, service_id = 1
E/	 ( 117): cby, conn_id = 2, client_id = 1, service_id = 1
W/libc ( 117): WARNING: generic atexit() called from legacy shared library
W/libc ( 117): WARNING: generic atexit() called from legacy shared library
D/AndroidRuntime( 443):
D/AndroidRuntime( 443): >>>>>> AndroidRuntime START com.android.internal.os.ZygoteInit <<<<<<
D/AndroidRuntime( 443): CheckJNI is OFF
D/dalvikvm( 443): DexOpt: incorrect opt magic number (0xff ff ff ff)
W/dalvikvm( 443): Cached DEX '/system/framework/core.jar' (/data/dalvik-cache/system@framework@[email protected]) is
stale and not writable
I/dalvikvm( 443): Unable to open or create cache for /system/framework/core.jar (/data/dalvik-cache/system@framework@co
[email protected])
D/dalvikvm( 443): Unable to process classpath element '/system/framework/core.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/core-junit.jar (/data/dalvik-cache/system@framew
[email protected]@classes.dex)
D/dalvikvm( 443): Unable to process classpath element '/system/framework/core-junit.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/bouncycastle.jar (/data/dalvik-cache/system@fram
[email protected]@classes.dex)
D/dalvikvm( 443): Unable to process classpath element '/system/framework/bouncycastle.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/ext.jar (/data/dalvik-cache/system@framework@ext
.[email protected])
D/dalvikvm( 443): Unable to process classpath element '/system/framework/ext.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/framework.jar (/data/dalvik-cache/system@framewo
[email protected]@classes.dex)
D/dalvikvm( 443): Unable to process classpath element '/system/framework/framework.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/telephony-common.jar (/data/dalvik-cache/system@
[email protected]@classes.dex)
D/dalvikvm( 443): Unable to process classpath element '/system/framework/telephony-common.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/mms-common.jar (/data/dalvik-cache/system@framew
[email protected]@classes.dex)
D/dalvikvm( 443): Unable to process classpath element '/system/framework/mms-common.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/android.policy.jar (/data/dalvik-cache/system@fr
[email protected]@classes.dex)
D/dalvikvm( 443): Unable to process classpath element '/system/framework/android.policy.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/services.jar (/data/dalvik-cache/system@framewor
[email protected]@classes.dex)
D/dalvikvm( 443): Unable to process classpath element '/system/framework/services.jar'
E/dalvikvm( 443): Dex cache directory isn't writable: /data/dalvik-cache
I/dalvikvm( 443): Unable to open or create cache for /system/framework/apache-xml.jar (/data/dalvik-cache/system@framew
[email protected]@classes.dex)
D/dalvikvm( 443): Unable to process classpath element '/system/framework/apache-xml.jar'
E/dalvikvm( 443): No valid entries found in bootclasspath '/system/framework/core.jar:/system/framework/core-junit.jar:
/system/framework/bouncycastle.jar:/system/framework/ext.jar:/system/framework/framework.jar:/system/framework/telephony
-common.jar:/system/framework/mms-common.jar:/system/framework/android.policy.jar:/system/framework/services.jar:/system
/framework/apache-xml.jar'
E/dalvikvm( 443): VM aborting
F/libc ( 443): Fatal signal 11 (SIGSEGV) at 0xdeadd00d (code=1), thread 443 (zygote)
I/DEBUG ( 106): failed to open tombstone file '/data/tombstones/tombstone_00': No such file or directory
I/Netd ( 518): Netd 1.0 starting
W/InterfaceController( 518): Warning (Cannot load library: load_library(linker.cpp:771): library "/system/lib/libnetcmd
iface.so" not found) while opening the net interface command library
I/mediaserver( 517): ServiceManager: 0x40b18f90
I/AudioFlinger( 517): Using default 3000 mSec as standby time.
I/CameraService( 517): CameraService started (pid=517)
E/QualcommCamera( 517): Qint android::get_number_of_cameras(): E
I/QualcommCameraHardware( 517): getCameraInfo: IN
I/QualcommCameraHardware( 517): getCameraInfo: loading libqcamera at 0x4003fed8
V/QualcommCameraHardware( 517): Storing the current target type as 3
I/QualcommCameraHardware( 517): getCameraInfo: numOfCameras = 1
I/QualcommCameraHardware( 517): Camera sensor 0 info:
I/QualcommCameraHardware( 517): camera_id: 0
I/QualcommCameraHardware( 517): modes_supported: 5
I/QualcommCameraHardware( 517): position: 0
I/QualcommCameraHardware( 517): sensor_mount_angle: 0
V/QualcommCameraHardware( 517): getCameraInfo: dlclose(libqcamera)
I/QualcommCameraHardware( 517): getCameraInfo: OUT
I/AudioPolicyManagerBase( 517): loadAudioPolicyConfig() loaded /system/etc/audio_policy.conf
I/AudioHardwareMSM76XXA( 517): get_audpp_filter
I/AudioHardwareMSM76XXA( 517): open /system/etc/AudioFilter.csv success.
I/AudioHardwareMSM76XXA( 517): EQ flag = 00.
I/AudioHardwareMSM76XXA( 517): EQ flag = 00.
I/AudioHardwareMSM76XXA( 517): EQ flag = 00.
E/AudioHardwareMSM76XXA( 517): failed to open AUTO_VOLUME_CONTROL /system/etc/AutoVolumeControl.txt: No such file or di
rectory (2)
D/AudioHardwareMSM76XXA( 517): Auto Volume Enabled= 0
I/AudioHardwareMSM76XXA( 517): Set master volume to 7.
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(0, 0, 7)
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(6, 0, 7)
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(12, 0, 7)
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(3, 0, 7)
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(16, 0, 7)
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(25, 0, 7)
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(8, 0, 1)
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(9, 0, 1)
I/AudioFlinger( 517): loadHwModule() Loaded primary audio interface from QCOM Audio HW HAL (audio) handle 1
I/AudioFlinger( 517): HAL output buffer size 1200 frames, normal mix buffer size 1200 frames
I/AudioMixer( 517): found effect "Multichannel Downmix To Stereo" from The Android Open Source Project
I/AudioFlinger( 517): Using module 1 has the primary audio interface
D/AudioHardwareInterface( 517): setMode(NORMAL)
E/	 ( 107): cby, conn_id = 0, client_id = 2, service_id = 1
I/AudioFlinger( 517): AudioFlinger's thread 0x4004f008 ready to run
E/	 ( 107): cby, conn_id = 0, client_id = 3, service_id = 1
E/	 ( 107): cby, conn_id = 0, client_id = 1, service_id = 4
E/	 ( 107): cby, conn_id = 1, client_id = 2, service_id = 1
E/	 ( 107): cby, conn_id = 1, client_id = 3, service_id = 1
E/	 ( 107): cby, conn_id = 1, client_id = 1, service_id = 4
E/	 ( 107): cby, conn_id = 2, client_id = 2, service_id = 1
W/AudioFlinger( 517): Thread AudioOut_2 cannot connect to the power manager service
E/	 ( 107): cby, conn_id = 2, client_id = 3, service_id = 1
E/	 ( 107): cby, conn_id = 2, client_id = 1, service_id = 4
I/AudioHardwareMSM76XXA( 517): Routing audio to Speakerphone
W/AudioHardwareMSM76XXA( 517): rpc_snd_set_device(6, 1, 1)
D/AudioHardwareMSM76XXA( 517): setVoiceVolume(0.400000)
I/AudioHardwareMSM76XXA( 517): Setting in-call volume to 2 (available range is 2 to 7)
D/AudioHardwareMSM76XXA( 517): rpc_snd_set_volume(38, 0, 2)
I/audio_a2dp_hw( 517): adev_open: adev_open in A2dp_hw module
I/AudioFlinger( 517): loadHwModule() Loaded a2dp audio interface from A2DP Audio HW HAL (audio) handle 3
I/AudioPolicyService( 517): Loaded audio policy from QCOM Audio Policy HAL (audio_policy)
W/libc ( 107): WARNING: generic atexit() called from legacy shared library
E/	 ( 107): cby, conn_id = 1, client_id = 4, service_id = 1
E/	 ( 107): cby, conn_id = 1, client_id = 5, service_id = 1
E/	 ( 107): cby, conn_id = 0, client_id = 1, service_id = 224
D/MDnsDS ( 518): MDnsSdListener::Hander starting up
D/MDnsDS ( 518): MDnsSdListener starting to monitor
D/MDnsDS ( 518): Going to poll with pollCount 1

Edited by capoeirabg, 29 April 2013 - 08:17 AM.

  • 0

#10
dRJoker4o0

dRJoker4o0

    Newbie

  • Members
  • Pip
  • 15 posts
  • Devices:ZTE Blade III
I have same problem. Please help...

  • 0

#11
Snowscape

Snowscape

    Newbie

  • Members
  • Pip
  • 14 posts
  • Gender:Male
  • Location:Bielsko-Biała, Poland
  • Devices:ZTE Blade III
I see the problem is still unsolved, so maybe this will help a little bit.
I had had the same problem with phone freezing on the bootanimation, but after a few attempts it managed to finish booting. But it was catching freezes at random moments, while I was using it, as someone mentioned before. I had pulled out sd card to check if this was its error, but it didn't solve the problem. Then I started to play around with cpu governors and overclocking. And when I'd set the governor to "performance", so the one that fixes the cpu at constant frequency I found that the freezes were totally gone. Well, it would sometimes freeze on reboot, but I could normally use the phone. Attempts of changing cpu frequency (didn't matter if I was lowering it or boosting) were causing instant hang. Another clue is the fact that after such a freeze, while rebooting the phone the "Android is upgrading" screen was appearing, like dalvik cache had been wiped.
It happens only on JB roms, ICS works fine.
So the temporary fix is, once it finish boot, to set the governor to performance. Battery drains pretty fast, though.

Edited by Snowscape, 09 June 2013 - 08:48 AM.

  • 0

#12
peetu20

peetu20

    Addict

  • Members
  • PipPipPipPipPip
  • 927 posts
  • Gender:Male
  • Location:Finland
  • Devices:Zte Blade, Zte Blade III

I see the problem is still unsolved, so maybe this will help a little bit.
I had had the same problem with phone freezing on the bootanimation, but after a few attempts it managed to finish booting. But it was catching freezes at random moments, while I was using it, as someone mentioned before. I had pulled out sd card to check if this was its error, but it didn't solve the problem. Then I started to play around with cpu governors and overclocking. And when I'd set the governor to "performance", so the one that fixes the cpu at constant frequency I found that the freezes were totally gone. Well, it would sometimes freeze on reboot, but I could normally use the phone. Attempts of changing cpu frequency (didn't matter if I was lowering it or boosting) were causing instant hang. Another clue is the fact that after such a freeze, while rebooting the phone the "Android is upgrading" screen was appearing, like dalvik cache had been wiped.
It happens only on JB roms, ICS works fine.
So the temporary fix is, once it finish boot, to set the governor to performance. Battery drains pretty fast, though.

Setting governor to perfomance will drain ur battery in one day. It keeps cpu at high clocks all the time, so ur device do not get to sleepmode, so you can use it about 10 hours I think before you need to charge :D

  • 0

#13
Snowscape

Snowscape

    Newbie

  • Members
  • Pip
  • 14 posts
  • Gender:Male
  • Location:Bielsko-Biała, Poland
  • Devices:ZTE Blade III

Setting governor to perfomance will drain ur battery in one day. It keeps cpu at high clocks all the time, so ur device do not get to sleepmode, so you can use it about 10 hours I think before you need to charge :D

Exactly, I'm aware of this. The battery lasts about 15-17 hours of moderate use on performance governor. It's the only way to get rid of those freezes and be able to run JB I've found so far though. But I'm not a dev and don't have knowledge to look for the solution somewhere deeper.
Well, other way is to revert back to ICS ;)

  • 0

#14
peetu20

peetu20

    Addict

  • Members
  • PipPipPipPipPip
  • 927 posts
  • Gender:Male
  • Location:Finland
  • Devices:Zte Blade, Zte Blade III

Exactly, I'm aware of this. The battery lasts about 15-17 hours of moderate use on performance governor. It's the only way to get rid of those freezes and be able to run JB I've found so far though. But I'm not a dev and don't have knowledge to look for the solution somewhere deeper.
Well, other way is to revert back to ICS ;)

Then its ok, I can live with my blade I, battery drains empty in one day with default use.

  • 0

#15
daliborhes

daliborhes

    Newbie

  • Members
  • Pip
  • 36 posts
  • Gender:Male
  • Location:Serbia
  • Devices:ZTE Blade 3

I had had the same problem with phone freezing on the bootanimation, but after a few attempts it managed to finish booting. But it was catching freezes at random moments, while I was using it, as someone mentioned before. I had pulled out sd card to check if this was its error, but it didn't solve the problem. Then I started to play around with cpu governors and overclocking. And when I'd set the governor to "performance", so the one that fixes the cpu at constant frequency I found that the freezes were totally gone. Well, it would sometimes freeze on reboot, but I could normally use the phone. Attempts of changing cpu frequency (didn't matter if I was lowering it or boosting) were causing instant hang. Another clue is the fact that after such a freeze, while rebooting the phone the "Android is upgrading" screen was appearing, like dalvik cache had been wiped.
It happens only on JB roms, ICS works fine.
So the temporary fix is, once it finish boot, to set the governor to performance. Battery drains pretty fast, though.


I had exactly the same problem flashing jelly bean roms. However, this post helped me a lot. So far I have managed to install CM 10 by KonstaT and Pacman rom and setting governer to "performance", emmediately after booting, made this roms stable. No more freezing for me, except while rebooting, but I can live with that. :) Now, is there an easy solution for setting "performance" as default governer? I do not have the knowledge to deal with editing kernel or something like that but I'm very much involved in basic stuff! :) Thanks in advance.

  • 0

#16
Snowscape

Snowscape

    Newbie

  • Members
  • Pip
  • 14 posts
  • Gender:Male
  • Location:Bielsko-Biała, Poland
  • Devices:ZTE Blade III

I had exactly the same problem flashing jelly bean roms. However, this post helped me a lot. So far I have managed to install CM 10 by KonstaT and Pacman rom and setting governer to "performance", emmediately after booting, made this roms stable. No more freezing for me, except while rebooting, but I can live with that. :) Now, is there an easy solution for setting "performance" as default governer? I do not have the knowledge to deal with editing kernel or something like that but I'm very much involved in basic stuff! :) Thanks in advance.

Simply tick "set on boot" option in cpu settings. This won't fix freezes on reboot though. Apparently the governor is being set at the end of booting process.

  • 0

#17
daliborhes

daliborhes

    Newbie

  • Members
  • Pip
  • 36 posts
  • Gender:Male
  • Location:Serbia
  • Devices:ZTE Blade 3

Simply tick "set on boot" option in cpu settings. This won't fix freezes on reboot though. Apparently the governor is being set at the end of booting process.

Of course, that's the first thing I did. I meant solution about editing rom (scripts in .zip file or something like that) before instaling, to get rid of the freezes, if it's possible. I want to try other roms like CM 10.1 or MIUI because I wasn't being able to boot them at all.

  • 0

#18
KonstaT

KonstaT

    Hardcore

  • Developer Team
  • PipPipPipPipPipPip
  • 2,679 posts
  • Gender:Male
  • Location:Finland
  • Devices:Moto G, ZTE Open C
  • Twitter:@konstatuomio

Setting governor to perfomance will drain ur battery in one day. It keeps cpu at high clocks all the time, so ur device do not get to sleepmode, so you can use it about 10 hours I think before you need to charge :D

Not a single thing is true in that post. :P

I had exactly the same problem flashing jelly bean roms. However, this post helped me a lot. So far I have managed to install CM 10 by KonstaT and Pacman rom and setting governer to "performance", emmediately after booting, made this roms stable. No more freezing for me, except while rebooting, but I can live with that. :) Now, is there an easy solution for setting "performance" as default governer? I do not have the knowledge to deal with editing kernel or something like that but I'm very much involved in basic stuff! :) Thanks in advance.

Well, that's hardly a solution or even a proper work a round.

People who suffer from this should try finding commons factors in your devices instead (stock firmware version, hardware revision, etc). Maybe even try flashing a different stock firmware first. Official ZTE updates also include bootloaders and radio firmware that are not changed when you flash a custom ROMs. Does Aurora Borealis crash if you set CPU governor to something other than performance? Stock ROMs default to performance governor for some reason.

And to your questions, you can place a simple script to /system/etc/init.d/ to change governor during booting.
#!/system/bin/sh
echo "performance" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor

  • 0

#19
daliborhes

daliborhes

    Newbie

  • Members
  • Pip
  • 36 posts
  • Gender:Male
  • Location:Serbia
  • Devices:ZTE Blade 3

Well, that's hardly a solution or even a proper work a round.

People who suffer from this should try finding commons factors in your devices instead (stock firmware version, hardware revision, etc). Maybe even try flashing a different stock firmware first. Official ZTE updates also include bootloaders and radio firmware that are not changed when you flash a custom ROMs. Does Aurora Borealis crash if you set CPU governor to something other than performance? Stock ROMs default to performance governor for some reason.

And to your questions, you can place a simple script to /system/etc/init.d/ to change governor during booting.

#!/system/bin/sh
echo "performance" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor

I managed to use your CM 10, so it's at least a partial solution for me. The rom works now without freezes and since I don't turn off or restart my phone, I can be satisfied. In addition, there is a similar problem in my country with Huawei g300 phones and the people solved it with instaling a stock rom with diferent baseband. After that, they didn't have problem instaling roms so that's my next move. I will try to flash a different stock rom when I have time. Anyway, thanks for the reply.

  • 0

#20
daliborhes

daliborhes

    Newbie

  • Members
  • Pip
  • 36 posts
  • Gender:Male
  • Location:Serbia
  • Devices:ZTE Blade 3
Oh I forgot to answer your question. Aurora booted and worked like a charm, no crashes when I change governor or overclock the device. Same thing with WorldEndBefore rom. Only Jelly Bean based roms had freezes and reboots.

  • 0




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users