Guest SuperGiGi2 Posted October 15, 2011 Report Share Posted October 15, 2011 If I am on 2.1 and I only need to use the qsd8250_semc command file... how do I do it? Does the phone need to be on? Or I should connect it while off, pressing the back button, to enter flash mode? This isn's clearly specified nowhere. Link to comment Share on other sites More sharing options...
Guest basti2909 Posted October 15, 2011 Report Share Posted October 15, 2011 If I am on 2.1 and I only need to use the qsd8250_semc command file... how do I do it? Does the phone need to be on? Or I should connect it while off, pressing the back button, to enter flash mode? This isn's clearly specified nowhere. As Seen in op Turn your phone ON and right after the vibration connect your USB cable again to your PC. 4. Start the qsd8250_semc.cmd file from QSD8250 folder 5. WHEN flashtool recognizes your phone (root permitions and some other buttons can be pressed) CLOSE flashtool and press any key on qsd8250_semc window 6. If the process will succeed you´ll get something like this: process requires standard 2.x android firmware.Press any key to continue . . .Getting ROOT rights.1464 KB/s (585731 bytes in 0.390s)error: protocol fault (no status)Waiting ...Removing NAND MPU restrictions via SEMC backdoor. Permanent. Require ROOT rights.192 KB/s (3087 bytes in 0.015s)successWaiting ...Getting ROOT rights.Waiting ...Writing patched semcboot. Two step processFirst, we need get access to semcboot area504 KB/s (8064 bytes in 0.015s)Second, we need to write semcboot ;)1531 KB/s (588236 bytes in 0.375s)successfully wrote 0001ff80Press any key to continue . . . 7. Now run Kernel Upgrade file on flashtool 8. Reboot and try to enter on xRecovery and Wipe Dalvik-Cache 9. Reboot your phone and copy/paste the dowloaded wifi modules from SDCARD to the correct places with root explorer (or something like that). On every pasted files long press, set permitions on every boxes note: these files (both) should go to /system/lib/modules 10. Power OFF your phone and flash your kernel choice (Stock or Doom´s one) through flashtool Link to comment Share on other sites More sharing options...
Guest SuperGiGi2 Posted October 15, 2011 Report Share Posted October 15, 2011 Thanks, but I am on 2.1. Don't need to do this, only what the_laser said in the original thread. But, I am not quite sure about the on/off. Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 19, 2011 Report Share Posted October 19, 2011 I got a question! After I flashed Kernel Downgrade pull off my usb cable and turned on my phone I pulled the usb cabel in my pc right after the vibration. The Phone stucks at SE logo. But Flashtool isn't recognizing my phone ! Some ideas? dude i have the same problem as yours,,,,can u tell me how u got it working?thanks Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 19, 2011 Report Share Posted October 19, 2011 Refering to your step 5,,,flashtool is not recognising my phone,,wat to do? Link to comment Share on other sites More sharing options...
Guest ooops! Posted October 19, 2011 Report Share Posted October 19, 2011 Refering to your step 5,,,flashtool is not recognising my phone,,wat to do? make sure you use 2.9 version of flashtool. i also had big issues like that on v3 Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 20, 2011 Report Share Posted October 20, 2011 make sure you use 2.9 version of flashtool. i also had big issues like that on v3 i am using 2.9 version only dude,,still no good Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 20, 2011 Report Share Posted October 20, 2011 (edited) i am using 2.9 version only dude,,still no good 18/023/2011 13:23:27 - INFO - <- This level is successfully initialized 18/023/2011 13:23:37 - INFO - Connected device : X10 18/023/2011 13:23:38 - INFO - Installed version of busybox : BusyBox v1.19.0.git.adrynalyne (2010-12-21 22:03:30 MST) multi-call binary. 18/018/2011 14:18:40 - INFO - Preparing files for flashing 18/018/2011 14:18:43 - INFO - Searching Xperia.... 18/018/2011 14:18:44 - ERROR - Please plug you device in flash mode 18/018/2011 14:18:45 - INFO - Searching Xperia.... 18/018/2011 14:18:45 - ERROR - Please plug you device in flash mode 18/018/2011 14:18:46 - INFO - Searching Xperia.... 18/018/2011 14:18:56 - INFO - Searching Xperia.... 18/018/2011 14:18:56 - INFO - Found at USB\VID_0FCE&PID_ADDE\6&11B5CB24&0&3 18/018/2011 14:18:56 - INFO - Start Flashing 18/018/2011 14:18:56 - INFO - VER="R8A013";DATE="20100119";TIME="17:24:00"; 18/018/2011 14:18:56 - INFO - Flashing loader 18/019/2011 14:19:00 - INFO - PROT_VER="02";DATE="20091222";TIME="15:39:00";VER="R4A024";CXC="1226-2250";TYPE="S1_LOADER";UNIQUE_DEV_ID="41E9043E8B4BC770432F45A8808516343543CFE4";SEC_LOCK_STATUS="LOCKED";OTP_DATA="4BBD77004714040209480430F9D81D70F0C32000";IMEI="35941903804363";AID_VERSION="0004";EROM_AID="0001";LOADER_AID="0001";SW_AID="0001";CUST_AID="0001";SIM_LOCK_AID="0001";HWCONF_AID="0001";PROD_AID="0000";ACTIVE_LOADER_AID="0001";MAN_ID="002C";DEV_ID="00B3";SIN_VER="0001";AID_TAMP="NOT_TAMPERED";MAX_PKT_SZ="00010000";AUTH_LEVEL="NONE";AUTH_MET="0001";CARD_PRESENT="YES";CARD_SIZE="8GB";CARD_DATA="";LOADER_ROOT="S1_Loader_Root_f851";EROM_ROOT="S1_EROM_Root_b15e";SW_ROOT="S1_SW_Root_ac12";CUST_ROOT="S1_Cust_Root_5789";SIM_LOCK_ROOT="S1_SL_Root_f20d";HW_CONF_ROOT="S1_HWConf_Root_ee5d"; 18/019/2011 14:19:02 - INFO - Flashing kernel.sin 18/019/2011 14:19:07 - INFO - Flashing finished. 18/019/2011 14:19:07 - INFO - Now unplug the device and power it on 18/019/2011 14:19:07 - INFO - Then go to application settings 18/019/2011 14:19:07 - INFO - turn on Unknown Sources and Debugging 18/020/2011 14:20:10 - INFO - Connected device : X10 18/020/2011 14:20:12 - INFO - Installed version of busybox : BusyBox v1.19.0.git.adrynalyne (2010-12-21 22:03:30 MST) multi-call binary. the process halts after this i read somewhere that i should check my drivers in flashtool,,any one having any idea? Edited October 20, 2011 by abhix10 Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 21, 2011 Report Share Posted October 21, 2011 hey pple plz help me,,,i want to unlock the bootloader,,, Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 22, 2011 Report Share Posted October 22, 2011 No there is nothing Flashtool is only showing the last line after flashing and i can't use the butttons. And I'm using 3.0.0 i am using flashtool 2.9 ,,,after i ahve downgraded the phone and then reconnect and start the batch file,,,the flashtool says connected x 10 and shows the busy box number,,,,but doesnt proceeds further when i connect the phone for second time ie after downgrading,,i hear the sound of connecting (which one usually hears whenever a device is connected)my pc companion prompts me to connect the phone but suddenly i hear the sound of getting disconnected,....what is the problem? Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 23, 2011 Report Share Posted October 23, 2011 ,,hey guys this is a video of the above guide but i am using it to explain my problem whats not happening with my x10 is at 3:10 u will see that the x10 is recognised as if a new device is connected,,,this is not happening with me,,,any suggestions? Link to comment Share on other sites More sharing options...
Guest rendeiro2005 Posted October 24, 2011 Report Share Posted October 24, 2011 ,,hey guys this is a video of the above guide but i am using it to explain my problem whats not happening with my x10 is at 3:10 u will see that the x10 is recognised as if a new device is connected,,,this is not happening with me,,,any suggestions? like i said in the OP. Use flashtool 2.9 Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 25, 2011 Report Share Posted October 25, 2011 (edited) like i said in the OP. Use flashtool 2.9 like i said the prob is coming while i am using 2.9 Edited October 25, 2011 by abhix10 Link to comment Share on other sites More sharing options...
Guest rendeiro2005 Posted October 25, 2011 Report Share Posted October 25, 2011 like i said the prob is coming while i am using 2.9 ohhh i didn´t realize that, sorry;) ok, try to remove ALL your SE apps from PC (SEUS, PCC and if you install usb drivers that came with flashtool remove that aswell). then: reboot your pc reboot your phone connect your phone to pc and see if usb drivers will install automatically. install from SE web page thas version of PCC and SEUS install usb drivers from flashtool reboot both see how it goes... Link to comment Share on other sites More sharing options...
Guest abhix10 Posted October 31, 2011 Report Share Posted October 31, 2011 (edited) ohhh i didn´t realize that, sorry;) ok, try to remove ALL your SE apps from PC (SEUS, PCC and if you install usb drivers that came with flashtool remove that aswell). then: reboot your pc reboot your phone connect your phone to pc and see if usb drivers will install automatically. install from SE web page thas version of PCC and SEUS install usb drivers from flashtool reboot both see how it goes... what i have figured out is when i reconnect my phone after downgrading kernel,,my pc companion asks me to select connect phone option by dragging the notification bar(which normally happens whenever we connect x10 to pc),,but since i have used the downgrade kernel all i see on my x10 is SE logo (which normally happens after using the downgrade kernel,,,so how can i make the pc companion recognize my phone ? in step 3 when i reconnect my phone,,the pc companion asks me to drag the notification bar and press connect phone ,,,but i have already downgraded as in step one,,all my phone shows is se logo(which normally happens if we use downgrade kernel) ,,so how can i connect the phone in pc companion,, Edited October 31, 2011 by abhix10 Link to comment Share on other sites More sharing options...
Guest abhix10 Posted November 4, 2011 Report Share Posted November 4, 2011 what i have figured out is when i reconnect my phone after downgrading kernel,,my pc companion asks me to select connect phone option by dragging the notification bar(which normally happens whenever we connect x10 to pc),,but since i have used the downgrade kernel all i see on my x10 is SE logo (which normally happens after using the downgrade kernel,,,so how can i make the pc companion recognize my phone ? in step 3 when i reconnect my phone,,the pc companion asks me to drag the notification bar and press connect phone ,,,but i have already downgraded as in step one,,all my phone shows is se logo(which normally happens if we use downgrade kernel) ,,so how can i connect the phone in pc companion,, unlocked the bootlader by reverting back to 2.1 Link to comment Share on other sites More sharing options...
Guest modacool Posted November 6, 2011 Report Share Posted November 6, 2011 Hi All. I just tried this procedure and after flashing with flashtool for the first time. I unplug the phone, turn it on and quickly plug it in but the phone remains in a blank state, no logo or nothing. flashtool does not detect it. Phone is new and unlocked with code. I'd appreciate your help. Link to comment Share on other sites More sharing options...
Guest abhix10 Posted November 7, 2011 Report Share Posted November 7, 2011 Hi All. I just tried this procedure and after flashing with flashtool for the first time. I unplug the phone, turn it on and quickly plug it in but the phone remains in a blank state, no logo or nothing. flashtool does not detect it. Phone is new and unlocked with code. I'd appreciate your help. first of all ,,did u check the status of your phone (whether the bootloader can be unlocked or not)using setools given in the first post? Link to comment Share on other sites More sharing options...
Guest modacool Posted November 7, 2011 Report Share Posted November 7, 2011 nevermind. Managed to do it. had a problem with the drivers Link to comment Share on other sites More sharing options...
Guest gogogu Posted December 16, 2011 Report Share Posted December 16, 2011 I get a 404 when trying to get any of the wifi modules? Link to comment Share on other sites More sharing options...
Guest rendeiro2005 Posted December 16, 2011 Report Share Posted December 16, 2011 I get a 404 when trying to get any of the wifi modules? All wifi modules are from devs links. You'd better search over xda forums. Link to comment Share on other sites More sharing options...
Guest ahmadzxc Posted June 11, 2012 Report Share Posted June 11, 2012 hi every body i have the same proplem about flashtool recognizing my x10i and this is the thread to let you see a whole picture http://forum.xda-developers.com/showthread.php?t=1697497 i tried all the suggestion in it and nothing is work i hope you guys can help thanks Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now