Guest Buzing Bee Posted November 15, 2010 Report Share Posted November 15, 2010 Here is my OverClocked kernel for the Desire HD. This kernel is undervolted all the way up to 1.1ghz and uses a maximum overvolt of 150mV at 1.53ghz I AM NOT RESPONSABLE FOR ANY DAMAGE CAUSED BY THIS ALTHOUGH TESTED YOU UNDERTAKING THIS MEANS U UNDERSTAND AND TAKE THE RISKS like my undervolted kernel clock speeds under 1209MHz are undervolted in comparison with stock and 1209Mhz is at the same voltage as stock. Above the system is at a hight voltage than stock slighly. This KERNEL is for people woh dont mind going highet voltage than stock. If this isnt you check out my UV kernel As the DesireHD has a slightly better quiality CPU than the Z/G2 this over volt can be slightly less on this. I cannot guarrentee that this kernel will be stable on all DesireHD's if you get freezing/crashing limit the CPU speed in setCPU or install my UV kernel. [CHANGELOG] 0.0.4 -- Enabled Kernel Debugging (no performance gains just nice to have for devs) -- Tweaked speeds at max stock voltage frim 1.24Ghz down to 1.22Ghz (As there where a few issues with boot looping) 0.0.3 -- Kernel version upgraded from 2.6.32.21 to 2.6.32.25 (Bug thanks to Mr. X for teaching me how to patch up the kernel ) -- Max Speed tweaked once more to 1.53Ghz (This is the final max speed if there are no issues) -- Few more optimisations 0.0.2 -- Added Conservative Governor -- Removed UserSpace Governor -- Puhsed Up the Overclock speeds slightly to get more out of the overvolt -- Max Speed is 1.51Ghz @ +150mv -- Some Build Optimisations 0.0.1 -- Inital Realease [iNSTALL] As we as yet dont have Clockwork Mod recovery its two steps to install. What You Need -- Fastboot Set Up -- This RAR file -- ADB set up -- Set CPU -- S-OFF HBOOT 1) boot into bootloader (fatboot mode) 2) put the zImage from the .rar file in the fastboot directoy 3) run fastboot flash zimage zImage 5) run fastboot reboot 6) wait for android to boot ///// Make shure you have the .ko from the .zip / .rar where the zImage came from /////// 7) put the .ko frile from the .rar file in your adb director 8)run adb push bcm4329.ko /sdcard/ 9) in adb shell run these commands in order su mount -o remount,rw /dev/block/mmcblk0p25 /system rm /system/lib/modules/bcm4329.ko busybox cp /sdcard/bcm4329.ko /system/lib/modules/bcm4329.ko rm /sdcard/bcm4329.ko 10) reboot 11) use SetCPU to gain the extra speed ****Due to the init bug (100% CPU usage use SetCPU to limit speed when screen off to save your battery I recommend 256 to 768***** Here is the zip to flash in clockwork too ... when its out :-D Just For Reference :- Speed / Voltage Chart for 0.0.2 Clock Voltage Stock Voltage 245760, 1000, 1000 368640, 1050 1050 768000, 1050, 1100 806400, 1050 1100 1017600, 1050 1100 1113600, 1050 ------ 1228800, 1100, ------ 1324800, 1150, ------ 1420800, 1200 ------ 1516800, 1250 ----- [ALL VERSIONS] 0.0.4 0.0.3 0.0.2 I have left the 0.0.1 kernel attached as well incase if any unforseen issues Credits Cyanogen team for info on edition speed tables -Mr. X- For helping me fix the scource Aplharev ppl for help Link to comment Share on other sites More sharing options...
Guest envynexxus Posted November 18, 2010 Report Share Posted November 18, 2010 Here is my OverClocked kernel for the Desire HD. This kernel is undervolted all the way up to 1.1ghz and uses a maximum overvolt of 150mV at 1.53ghz I AM NOT RESPONSABLE FOR ANY DAMAGE CAUSED BY THIS ALTHOUGH TESTED YOU UNDERTAKING THIS MEANS U UNDERSTAND AND TAKE THE RISKS like my undervolted kernel clock speeds under 1209MHz are undervolted in comparison with stock and 1209Mhz is at the same voltage as stock. Above the system is at a hight voltage than stock slighly. This KERNEL is for people woh dont mind going highet voltage than stock. If this isnt you check out my UV kernel As the DesireHD has a slightly better quiality CPU than the Z/G2 this over volt can be slightly less on this. I cannot guarrentee that this kernel will be stable on all DesireHD's if you get freezing/crashing limit the CPU speed in setCPU or install my UV kernel. [CHANGELOG] 0.0.4 -- Enabled Kernel Debugging (no performance gains just nice to have for devs) -- Tweaked speeds at max stock voltage frim 1.24Ghz down to 1.22Ghz (As there where a few issues with boot looping) 0.0.3 -- Kernel version upgraded from 2.6.32.21 to 2.6.32.25 (Bug thanks to Mr. X for teaching me how to patch up the kernel ) -- Max Speed tweaked once more to 1.53Ghz (This is the final max speed if there are no issues) -- Few more optimisations 0.0.2 -- Added Conservative Governor -- Removed UserSpace Governor -- Puhsed Up the Overclock speeds slightly to get more out of the overvolt -- Max Speed is 1.51Ghz @ +150mv -- Some Build Optimisations 0.0.1 -- Inital Realease [iNSTALL] As we as yet dont have Clockwork Mod recovery its two steps to install. What You Need -- Fastboot Set Up -- This RAR file -- ADB set up -- Set CPU -- S-OFF HBOOT 1) boot into bootloader (fatboot mode) 2) put the zImage from the .rar file in the fastboot directoy 3) run 5) run 6) wait for android to boot ///// Make shure you have the .ko from the .zip / .rar where the zImage came from /////// 7) put the .ko frile from the .rar file in your adb director 8)run 9) in adb shell run these commands in order 10) reboot 11) use SetCPU to gain the extra speed ****Due to the init bug (100% CPU usage use SetCPU to limit speed when screen off to save your battery I recommend 256 to 768***** Here is the zip to flash in clockwork too ... when its out :-D Just For Reference :- Speed / Voltage Chart for 0.0.2 Clock Voltage Stock Voltage 245760, 1000, 1000 368640, 1050 1050 768000, 1050, 1100 806400, 1050 1100 1017600, 1050 1100 1113600, 1050 ------ 1228800, 1100, ------ 1324800, 1150, ------ 1420800, 1200 ------ 1516800, 1250 ----- [ALL VERSIONS] 0.0.4 0.0.3 0.0.2 I have left the 0.0.1 kernel attached as well incase if any unforseen issues Credits Cyanogen team for info on edition speed tables -Mr. X- For helping me fix the scource Aplharev ppl for help Where is the zip for flashing using clockwork ?? Link to comment Share on other sites More sharing options...
Guest AndyCr15 Posted November 21, 2010 Report Share Posted November 21, 2010 Wow, you had to quote the WHOLE post that is directly above your post and is in fact the ONLY post in this thread, to ask a one question line? Link to comment Share on other sites More sharing options...
Guest envynexxus Posted November 22, 2010 Report Share Posted November 22, 2010 Wow, you had to quote the WHOLE post that is directly above your post and is in fact the ONLY post in this thread, to ask a one question line? B) Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now