162 replies to this topic

[Jurgennn]

So. Let's see if I have gotten this correctly.
My phone was originally a gen1-device, I upgraded to gen2. To repartition now I need to use a gen1-gen2 TPT. Is this correct?

[Amphoras]

Jurgennn, on 04 March 2012 - 10:07 AM, said:

So. Let's see if I have gotten this correctly.
My phone was originally a gen1-device, I upgraded to gen2. To repartition now I need to use a gen1-gen2 TPT. Is this correct?

That should be right. You can use this app to check which type you should use.

[Jurgennn]

Amphoras, on 04 March 2012 - 03:20 PM, said:

That should be right. You can use this app to check which type you should use.

Thanks!

---EDIT---

Strange. It seems to think I have a Gen2 stock. It says i should use image.bin to update.
What's the worst thing that can happen if i use the wrong update?

Edited by Jurgennn, 04 March 2012 - 05:20 PM.

[Amphoras]

Jurgennn, on 04 March 2012 - 05:14 PM, said:

Thanks!

---EDIT---

Strange. It seems to think I have a Gen2 stock. It says i should use image.bin to update.
What's the worst thing that can happen if i use the wrong update?

It depends how you updated to Gen 2. The worst that can happen is that it will do nothing. If its the wrong type, it just won't start.

[Jurgennn]

Amphoras, on 04 March 2012 - 10:00 PM, said:

It depends how you updated to Gen 2. The worst that can happen is that it will do nothing. If its the wrong type, it just won't start.

Ah! I see. That's good. I updated quite early after the first TPTs updates were released for updating from G1 to G2 with one of those TPTs. I can't remember if it was by kallt_kaffe or wbaw though.

[Amphoras]

Jurgennn, on 04 March 2012 - 10:16 PM, said:

Ah! I see. That's good. I updated quite early after the first TPTs updates were released for updating from G1 to G2 with one of those TPTs. I can't remember if it was by kallt_kaffe or wbaw though.

Ah ok, in that case you have found the one problem with the app. If you upgraded using a very old TPT, then it will think you have a stock Gen 2 phone when really you need to use the Gen 1 to Gen 2 type TPTs.

[aggregator]

Hi Amphoras!
I installed your Gen3 v1a TPT, it works fine.
However it can't charged when phone's off. It boots when i connect it to the charger.

Can you make a custom sized (128/2/311) partition using these firmware? I used that before this, and no problem with charging.
Thank you!

[T3KO]

Cant get it to work.Same situation as Jurgennn.I cant get any of the TPTs to work with menu+Vol+ just boots into Android.
NVM worked dont even know what I did just tried it over and over...

Edited by T3KO, 15 March 2012 - 05:43 PM.

[HumaDroid]

How do i find out the size of my system partition?

[Amphoras]

HumaDroid, on 21 March 2012 - 02:21 PM, said:

How do i find out the size of my system partition?

You can use this app.

[saransh9]

how much battery is needed for a tpt i have 13% and my phone is not charging but the problem might get fixed with a tpt.

[Amphoras]

saransh9, on 21 March 2012 - 04:29 PM, said:

how much battery is needed for a tpt i have 13% and my phone is not charging but the problem might get fixed with a tpt.

13% is a bit low. If you're doing a TPT without a rom, it might be enough to finish it, but I don't know for sure. Have you tried cleaning the battery contacts? Sometimes that causes the phone not to charge properly.

[tcpaulh]

@saransh9: If your phone is charging up to 13%, leave it plugged in during tpt.

[saransh9]

tcpaulh, on 22 March 2012 - 08:32 AM, said:

@saransh9: If your phone is charging up to 13%, leave it plugged in during tpt.

Now I'm able to charge it with a USB cable but not with charger

[saransh9]

Btw.when I make my own tpt using your app and check out I get 10/12 matches is it normal.

[Amphoras]

saransh9, on 22 March 2012 - 08:51 AM, said:

Btw.when I make my own tpt using your app and check out I get 10/12 matches is it normal.

It is if you have created your own TPT with your own partition sizes. As long as it told you that it had finished building it successfully it should be ok to use.

[saransh9]

Amphoras, on 22 March 2012 - 04:09 PM, said:

It is if you have created your own TPT with your own partition sizes. As long as it told you that it had finished building it successfully it should be ok to use.

Ok I used tpt there was a error at 99% but then success
Edit: this is a known bug

Edited by saransh9, 22 March 2012 - 06:17 PM.

[jesuita]

A few time ago i used the get 1 to get 2 tpt, the one with 160mb system and 294 data.
Yesterday i used another tpt to increse system size since i wanted to try ICS.

Now im trying to revert back but cant get the tpt to work.
I put the image folder on the root of sdcard, remove the battery, power it on with power+volume up but the it does nothing..

What am i doing wrong?

[Andy58]

jesuita, on 23 March 2012 - 09:38 PM, said:

I put the image folder on the root of sdcard, remove the battery, power it on with power+volume up but the it does nothing..

What am i doing wrong?

Forgetting to press menu too?

[jesuita]

Ok,  now that was dumb!
I swear when i tpt'ed to a ics compatible image i didnt use the menum button..

Thanks