TG01 dead

[Guest montse68]

Hi guys I am new to the forum and today I decided to change the ROM and everything perfect, but I dropped to the floor and jump the battery, and not start the TG01, I give him to boot, toshiba screen comes and then the orange screen, but there is no more, try doing a Hard Reset, but does not work, forgive my English I am Spanish, and translate with google. Thank you.

[Guest The Real Mc Coy]

Ouch...

In my opinion your device is bricked. No other solution than returning back to after sales service.

We'll never say enough : when you flash device keep it on a stable surface and don't touch it until it's done.

[Guest stepw]

Hi guys I am new to the forum and today I decided to change the ROM and everything perfect, but I dropped to the floor and jump the battery, and not start the TG01, I give him to boot, toshiba screen comes and then the orange screen, but there is no more, try doing a Hard Reset, but does not work, forgive my English I am Spanish, and translate with google. Thank you.

If Hard reset doesn't work, there could be hardware issues (broken/stuck buttons). See if you can return/replace it. If not, there's no solution yet to unbrick it, AFAIK.

[Guest xdalover]

Ouch...

In my opinion your device is bricked. No other solution than returning back to after sales service.

We'll never say enough : when you flash device keep it on a stable surface and don't touch it until it's done.

Plus: Be sure that your battery is full charged!!! ((better) and besides, you are plugged)

[Guest montse68]

It is not broke, do not post the whole rom and therefore will not start, single-image starts thosiba orange and stays there

[Guest The Real Mc Coy]

I said BRICKED not broke. Bricked means you cannot boot anymore and are stuck on starting screen and cannot flash again. It occurs when flashing fails and particularly when flashing is aborted violently.

Edited December 14, 2009 by The Real Mc Coy

[Guest pcmarcel]

I think you look carefully if it doesn't work at all after the screen, or that you see a black screen with backlight.

If so read THIS to do a hard reset.

If your phone doesn't work at all after the splash screen, then I think you better bring your phone back ;)

[Guest montse68]

:) :) :) :)

TG01 alive through a http://www.htcspain.com/foro-f170/muerta-mi-tg01-t28851.html (excuse me)

Hello. The other day I changed the rom to a friend TG01 and when the process pk gave me everything but would not start. I would spend as yours: Toshiba screen, Splash Operator and then a black screen. In addition he recognized the pc but nothing more. Anyway, after many laps I managed to install the rom again directly from the SD. Espero que te sirva pq me I have avoided losing a friend.

I tell you: if qutas the lid on top of the battery and Sim'll just below a hole with a black cap: quíatala (is just a little stuck) and you'll see three contacts. The first thing you do is the following: format the card in FAT 32 and copy the folder with the rom *. prg tsw inside (I did with the English rom). I also copied the executable to the root of SDDL + (not the one that comes with the rom but midificado of MODAC) but I think it's not necessary. Then enter the micro sd in the slot and put the battery charge to 100% WORKS JUST IN CASE YOU

Finally you have to turn the phone but with short between the first and the third prong (I did it with a cable). If everything turns out as I begin the process of copying the rom as when you started from the browser: white screen where it tells you do not remove the battery and it ... Once you start charging the rom and no need to short across the contacts (with breaks for the fingers).

[Guest Nicus]

@montse68 You mean that there is way to launch bootloader by shorting 2 pins ? Can You ask someone who can better english to translate beacouse google translation don't have much sense...

[Guest darckreign1984]

@montse68 You mean that there is way to launch bootloader by shorting 2 pins ? Can You ask someone who can better english to translate beacouse google translation don't have much sense...

this metod its launch flash routine.you must remove the black tape from located behind the sim card

[Guest montse68]

this metod its launch flash routine.you must remove the black tape from located behind the sim card

Ok :)

Bridge + On "TG01" + micro sd (format the card in FAT 32) copy folder, prg and tg01_sddl+

When you start and exit load rom screen, remove the bridge, and wait for loading rom.

I do not speak English Translate with Google, sorry

[Guest tra33372]

You can click here

http://forum.xda-developers.com/showthread...990&page=33

there are English instructions about this trick

1.Does anyone try to flash ENG rom on Japanese device? (I mean by this trick coz the normal method is not work)

2.Is this method fix the bricked device from flashing Eng rom on Jap TG01?

Thanks mate

Edited January 20, 2010 by tra33372

[Guest Nicus]

You can click here

http://forum.xda-developers.com/showthread...990&page=33

there are English instructions about this trick

1.Does anyone try to flash ENG rom on Japanese device? (I mean by this trick coz the normal method is not work)

2.Is this method fix the bricked device from flashing Eng rom on Jap TG01?

Thanks mate

I've already found out where are these pins located :)

These posts on XDA are written by me, everyone should know about this method this is another step in direction of cooked roms :)

1. I don't know

2. It should fix but someone must try :)