Guest yukinoko Posted October 15, 2010 Report Posted October 15, 2010 I ran superboot and now I can't start my phone, when i power it up I see the ACER logo but it doesn't go to the Android screen and it just blacks out. I tried the buttons combo to get into recovery mode but all I get is this: Partition checksum Splash1:checksum = 8ba9da08 OK boot:checksum=33dd7f1 !=001ed108 **fail** recovery:checksum=2b8b7b4b !=00216b18 **fail** system:checksum =ea332e01 OK ======== <<FAIL>> I am connected to my PC but it doesn't detect it, so I can't do anything. Please advice me!
Guest Dario93 Posted October 15, 2010 Report Posted October 15, 2010 When you try buttons combo the phone must be disconnected from your PC. Howewer,if you don't have malez recovery,this won't be useful,so you should flash a bin,but remember that this will ERASE ALL YOUR DATA PERMANENTLY! If you don't know how to flash a .bin file from Acer (you can find them here: http://android.modaco.com/content/acer-liq...ct-collection/) go to this post with this guide made by me : http://android.modaco.com/content/acer-liq...-acer-liquid-e/ Sorry for my bad english! :) Best regards, Dario93
Guest yukinoko Posted October 15, 2010 Report Posted October 15, 2010 My phone is not detected by my PC, I can't flash anything if my PC can't detect it.
Guest Koki1337 Posted October 15, 2010 Report Posted October 15, 2010 Detach from the PC, take out battery for a few seconds, connect back and try again. Hold camera button FULLY, hold volume down and then hold power button. After vibrating 3 times at a fast rate, release all buttons and wait Without Malez recovery, you'll see an Android with an exclamation mark. Just wait and it'll factory reset your phone. Then you can connect your phone again to the PC and get detected! :)
Guest yukinoko Posted October 16, 2010 Report Posted October 16, 2010 I tried it, but when I press the buttons while its connected to the PC it just goes right to the error message. No vibrations or anything. When I do that without connected to the PC, i get the 3 quick vibrations, it goes to the ACER logo but blacks out. No Android at all :)
Guest Koki1337 Posted October 16, 2010 Report Posted October 16, 2010 I tried it, but when I press the buttons while its connected to the PC it just goes right to the error message. No vibrations or anything. When I do that without connected to the PC, i get the 3 quick vibrations, it goes to the ACER logo but blacks out. No Android at all :) How long did you wait for it? With stock recovery, it has about 5~10 minutes
Guest yukinoko Posted October 18, 2010 Report Posted October 18, 2010 How long did you wait for it? With stock recovery, it has about 5~10 minutes still nothing has happened, stucked at the error screen. I dont get any other icons, it always goes to acer logo then black out. Either that or the error message. I am using an Acer liquid A1 by the way, not a Liquid E
Guest Retnuhz Posted January 4, 2011 Report Posted January 4, 2011 still nothing has happened, stucked at the error screen. I dont get any other icons, it always goes to acer logo then black out. Either that or the error message. I am using an Acer liquid A1 by the way, not a Liquid E Was this ever fixed? I have the same problem now and need help!
Guest Harness Posted January 4, 2011 Report Posted January 4, 2011 (edited) Not paying attention tot opic, going to attempt to help new poster. What's wrong, guy? Edited January 4, 2011 by Harness
Guest fischschneehase Posted January 4, 2011 Report Posted January 4, 2011 try to vol up, camera and power the screen stays black but you can see that the phone is detected by the pc;)
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now