Jump to content

Streak 2.2 loses baseband

Guest passie42

By Guest passie42
in Dell Streak 5" - Streak.MoDaCo.com

 Share

Recommended Posts

Guest passie42

Guest passie42

Posted
Posted (edited)

Hey guys,

I followed and read so many threads but I dont know what to do anymore.

I flashed to the 315_12332_00 firmware on my Streak that I bought unlocked in the Netherlands.

Baseband now is GAUSB1A131500EU build 12332 and everything works!! (I did not write down the original 1.6 baseband number so I dont know what that was)

Butt......when I rebooted my Streak the GSM/3G services quit.

If I check the settings it now says baseband unknown!!!!! (?)

There is no way to get the GSM/3G functions back except for flashing the 315_12332_00 firmware again!

After first boot it's ok but after a reboot my baseband is gone again!

I tried a lot to downgrade but I can not get it to work :-(

I wanted to flash to the original state 1.6 and wait for my OTA update or flash to Streak_309_0_00 firmware.

How can I make this happen?

Although WiFi works the device really feels bricked right now, saved a long time to buy it :-(

Someone please, please help me

Kind regards Passie

Edited by passie42
Guest Techneut

Guest Techneut

Posted
Posted

Did you install Dell's PC-suite and Koush's recovery 2.0.5.1 first?

Use 'search' on this forum to find them, and follow the instructions to install them on your computer...

Only then, you will be able to flash the new baseband.

Sorry, but life is never easy... sigh.

Guest Techneut

Guest Techneut

Posted
Posted
315 has been sent out to EU streaks

309 is US baseband,

Sorry, for getting confused...

Of course, you are right, as usual.

Thanks for correcting me on this!

:P

Guest passie42

Guest passie42

Posted
Posted
315 has been sent out to EU streaks

309 is US baseband,

But I have the 315 installed!

I am so confused right now....

Guest passie42

Guest passie42

Posted
Posted
Did you install Dell's PC-suite and Koush's recovery 2.0.5.1 first?

Use 'search' on this forum to find them, and follow the instructions to install them on your computer...

Only then, you will be able to flash the new baseband.

Sorry, but life is never easy... sigh.

Yes, did a superboot.bat and a recovery.bat but no luck

Guest passie42

Guest passie42

Posted
Posted
Yes, did a superboot.bat and a recovery.bat but no luck

Well I did it now.....

streak keeps rebooting while the lights are flashing.

Cant use it anymore.

I am going to read the PDF and the go to bed. This make me tyred and sick because irl I am so busy to.

Thanx guys, so far!

Guest fards

Guest fards

Posted
Posted
Well I did it now.....

streak keeps rebooting while the lights are flashing.

Cant use it anymore.

I am going to read the PDF and the go to bed. This make me tyred and sick because irl I am so busy to.

Thanx guys, so far!

nnnnnnnnnnnnnnnoooooooooooo

superboot was for 1.6 !

you need to reflash teh boot.img from teh 2.2 build you have

Guest passie42

Guest passie42

Posted
Posted
nnnnnnnnnnnnnnnoooooooooooo

superboot was for 1.6 !

you need to reflash teh boot.img from teh 2.2 build you have

My Streak keeps on rebooting, no way I knowhow to break tuis loop.

Have the 315 on my sd Card as update.pkg , I reboot with THE volume pressed and choose update from pkg.

THE lights keep flashing and THE Dell keeps rebooting in à loop.

I REALLY read THE forums and searched Google! I am really trying but I really seem stuck here.

I am using a Nokia 6210i now........ OMG pls help me !!! :P

Guest fards

Guest fards

Posted
Posted
My Streak keeps on rebooting, no way I knowhow to break tuis loop.

Have the 315 on my sd Card as update.pkg , I reboot with THE volume pressed and choose update from pkg.

THE lights keep flashing and THE Dell keeps rebooting in à loop.

I REALLY read THE forums and searched Google! I am really trying but I really seem stuck here.

I am using a Nokia 6210i now........ OMG pls help me !!! :P

I've told you what to do.

Guest passie42

Guest passie42

Posted
Posted
I've told you what to do.

You mean Stevens way?

Thats where i get stuck at THE waiting for device.

Copyed all needed files like fileboot to à folder, stevens boot image to my device and ran the fileboot run commands from à DOS prompt.

Then it says waiting for device. Also posted this problem in that forum. It seems I am at à point I dont know what i am doing anymore :P

Guest fards

Guest fards

Posted
Posted (edited)
You mean Stevens way?

Thats where i get stuck at THE waiting for device.

Copyed all needed files like fileboot to à folder, stevens boot image to my device and ran the fileboot run commands from à DOS prompt.

Then it says waiting for device. Also posted this problem in that forum. It seems I am at à point I dont know what i am doing anymore :P

if its waiting for device then you need to either change the command or use different drivers .

to fix the issues with the flashing LEDS because YOU flashed the superboot, then YOU need to flash the BOOT.IMG from the correct rom that you have on there.

As I've already said 4 posts above and you inlcuded in the quote!

Edited by fards
Guest passie42

Guest passie42

Posted
Posted
if its waiting for device then you need to either change the command or use different drivers .

to fix the issues with the flashing LEDS because YOU flashed the superboot, then YOU need to flash the BOOT.IMG from the correct rom that you have on there.

As I've already said 4 posts above and you inlcuded in the quote!

Well, did everything I thought I muust do but now its really bricked!

Cant come into recovery or flash mode.

When I press on button only the lights burn, not possible to use the volume or the camera modes....

Did I really bricked it now?

PLS help me....

Guest passie42

Guest passie42

Posted
Posted
if its waiting for device then you need to either change the command or use different drivers .

to fix the issues with the flashing LEDS because YOU flashed the superboot, then YOU need to flash the BOOT.IMG from the correct rom that you have on there.

As I've already said 4 posts above and you inlcuded in the quote!

Well, did everything I thought I must do but now its really bricked!

Cant come into recovery or flash mode.

When I press the on button only the lights burn, not possible to use the volume or the camera buttons for flash modes....

Did I really bricked it now?

PLS help me....

Guest passie42

Guest passie42

Posted
Posted
Well, did everything I thought I muust do but now its really bricked!

Cant come into recovery or flash mode.

When I press on button only the lights burn, not possible to use the volume or the camera modes....

Did I really bricked it now?

PLS help me....

I used this thread http://forums.whirlpool.net.au/archive/1557150

I get stuck with the driver update for my X64 system.

The Qualcom device changes to a com port with a ! mark, so I am not able to use the qdl tool.

Whats going on? Is there nobody In the Netherlands that can help me if I stop by, I will pay for it!!

I just cant get it to work........ :P

  • 2 weeks later...
Guest nozza

Guest nozza

Posted
Posted

Sorry for the noob-ish question...

i updated to hyde's 2.2 but forgot to flash the new baseband so it now says unknown baseband. Obviously i need to flash the baseband but do i need to re-install hyde's 2.2. It's all about laziness really, if i don't have to i'd rather not do it!

thanks in advance

Guest adzman808

Guest adzman808

Posted
Posted
Sorry for the noob-ish question...

i updated to hyde's 2.2 but forgot to flash the new baseband so it now says unknown baseband. Obviously i need to flash the baseband but do i need to re-install hyde's 2.2. It's all about laziness really, if i don't have to i'd rather not do it!

thanks in advance

i've flashed BBs to Steve's ROMs without fac resets or re-flashing from clockwork, so should be ok to just flash the BB

Guest nozza

Guest nozza

Posted
Posted
i've flashed BBs to Steve's ROMs without fac resets or re-flashing from clockwork, so should be ok to just flash the BB

Cheers for that. i gave it a go and Success!

i'm getting the hang of how to do things but i must admit i'm guessing at what is actually happening in the background.

Good fun though and well worth it - 2.2 up and running and looking good :)

Guest adzman808

Guest adzman808

Posted
Posted

No worries,

I haven't got a clue what i'm doing, but I just follow the instructions and reap the rewards

A new bb seems to like a couple of restarts to get going.... But that may just be my dumb perception

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
 Share
Go to topic listing
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept