Guest vinukm07 Posted October 7, 2011 Report Posted October 7, 2011 I have a very typical problem. The phone i totally dead. 1. It doesnt charge and when i insert the cable for charging the send led just blinks once and goes off. When i leave it as it is for charging the phone really gets heated up very fast. 2. the phone doesnt start at all. Some times when i try some different combination of keys Like Vol Up + send + power i get the android logo and goes off. Not sure if its really a hardware or a software issue. I purchased the phone from UK and i am in India now so no warranty as well :(. Please help.
Guest plegdroid Posted October 7, 2011 Report Posted October 7, 2011 excuse my ignorance but is the power supply the same in India as the UK?
Guest vinukm07 Posted October 7, 2011 Report Posted October 7, 2011 excuse my ignorance but is the power supply the same in India as the UK? Power supply may not be same but same happens when i use USB as well.
Guest astrolo Posted October 7, 2011 Report Posted October 7, 2011 (edited) have you install a custom rom or you have stock rom ? have you got ClockWorkMod ? have you try clockworkmod ? start device and press "Vol - " and try to install e rom with gen1&gen2 support like giger stir fry look this too http://android.modac...ng-a-zte-blade/ Edited October 7, 2011 by astrolo
Guest vinukm07 Posted October 7, 2011 Report Posted October 7, 2011 have you install a custom rom or you have stock rom ? have you got ClockWorkMod ? have you try clockworkmod ? start device and press "Vol - " and try to install e rom with gen1&gen2 support like giger stir fry look this too http://android.modac...ng-a-zte-blade/ I had CM7.3 rom installed on the phone.
Guest WAWA72 Posted October 7, 2011 Report Posted October 7, 2011 I think your USB Pins are broken. When you want i can help you. I life in Germany.
Guest astrolo Posted October 8, 2011 Report Posted October 8, 2011 I had CM7.3 rom installed on the phone. how do you install cm7 ? tpt mode ? cwm mode ?.... have you try "power on" + "vol -" to enter in clockworkmod ? ( not power on, vol+ , home) you must have something like this
Guest Pierreism Posted October 9, 2011 Report Posted October 9, 2011 If it's not charging it might be the same thing I'm getting. Is there a squealing/sparking noise coming from the battery area when you try and charge it?
Guest vinukm07 Posted October 10, 2011 Report Posted October 10, 2011 If it's not charging it might be the same thing I'm getting. Is there a squealing/sparking noise coming from the battery area when you try and charge it? There are no noise etc. Just the send LED blinks once when i connect thats it. When i am connected to the PC with USB when i try with the key combinations than i hear abeep and its detects an unsupposrted USB Device. My irony is that i had given it to my brother and had all the clockwork etc installed on the SD Card. He has removed it and formated it so i am in a fix that i dont have any valid sd card to boot as well.
Guest PhenomHTX Posted October 10, 2011 Report Posted October 10, 2011 (edited) your motherboad is dead :-) you need to check fuse on PCB is should have 2K ohm Edited October 10, 2011 by PhenomHTX
Guest vinukm07 Posted October 11, 2011 Report Posted October 11, 2011 your motherboad is dead :-) you need to check fuse on PCB is should have 2K ohm Ooops .. I pray it isnt so.
Guest unrandomsam Posted October 11, 2011 Report Posted October 11, 2011 Do you have download mode working ? (Take the battery out and plug it in with both vol keys pressed) If you get a DFU serial port in windows then you get to use the wonderful V880 Tool (Kanged from hedgepigdaniels thread). Boot into download mode and set up connectionDownload and install the ZTE USB driver.Put your phone in download mode by turning it on with both volume buttons held down at the same time. The screen will remain black, but the notification LED should briefly flash red.Plug it into your computer. The phone should be recognised in windows device manager under “Ports (COM & LPT)” as “ZTE Handset Diagnostic Interface(DFU) (COMxx)”. Take note of the port number (xx). If your phone cannot turn on at all and the LED doesn’t flash, it is dead. Sorry about that. Flash firmwareDownload this file, which contains the ZTE flasher along with firmware to flash your phone with, and unzip it somewhere convenient.Run “Flasher.exe” from the extracted folder. Press the exclamation mark and login as administrator with the password “ZTEsmt123”.Under “SW Directory”, select the correct firmware folder inside the extracted folder (European Gen1 firmware or Chinese v880 Gen2 firmware). ONLY flash the one appropriate for your phone.Leave the default settings as they are – “download cefs” ticked, “no backup restore” selected, and “download” selected.Go to the “Option” menu and select “Port Config”. Set line 1 to the COM port that you observed in step 3, then press OK.Press the purple arrow next to line 1 and wait for your phone to be flashed. When finished it should boot into FTM mode. Edit "channel1.nvm" to hold IMEIIn the flasher folder, open the file “channel1.nvm” with HxD, or a hex editor of your choice.Go to offset 0x1215. The IMEI is stored between offset 0x1215 and 0x121C. You need to read your correct IMEI from behind your battery and enter it here like this:In 0x1215 put the first digit of your IMEI followed by A. For each successive pair of digits, enter the second digit followed by the first digit. For example: and IMEI of 123456789012345 would be recorded at 0x1215 as 1A 32 54 76 98 10 32 54. When done, save this file. Restore channel1.nvm to your phone [*]Make sure channel1.nvm is in the folder next to the flasher with the correct IMEI.[*]Connect your phone to your computer and turn on your phone with volume down held. It should boot into FTM mode.[*]In the flasher, select “restore NV” and “RF/BT/IMEI/unLock info”, and press the purple arrow next to line 1. Your IMEI will now be restored to your phone. Put clockworkmod in the recovery partition Take out the battery and turn on the phone. Clockworkmod should load.Clockworkmod is now installed to your phone’s boot partition. This means that if you install a ROM at this point you will overwrite clockworkmod. You must now flash the correct version of clockworkmod to the recovery partition.Go to “mounts and storage”, and select mount USB storage. Connect the phone to your computer and copy the correct version of clockworkmod as a zip file (Gen1 for European Gen1 firmware, Gen2 for Chinese firmware) to your SD card, then install it using clockworkmod.Restart your phone with volume down held. It should boot into clockworkmod. If it boots into FTM mode or does not progress pass the green android, reboot normally and make sure you flashed the correct version of clockworkmod.
Guest unrandomsam Posted October 11, 2011 Report Posted October 11, 2011 Think I had the same thing once. V880 tool fixed it
Guest vinukm07 Posted October 12, 2011 Report Posted October 12, 2011 Think I had the same thing once. V880 tool fixed it Whats the v880 tool ?
Guest vinukm07 Posted October 14, 2011 Report Posted October 14, 2011 When i try to go into download mode nothing happens. And after a while i remove battery and than insert it back i get a android robot screen for 30 secs and goes off. My compyter detects it as a unsupported usb device :(
Guest Sborovm Posted October 14, 2011 Report Posted October 14, 2011 I guess that your battery is dead and don't want to charge. Therefore you had green android only for few seconds and then the phone switched off. You have to replace the battery and charge the new one with normal charger, no USB form PC! Do you have someone with the same phone to test with another battery? Maybe it helps B)
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now