Guest hachete Posted September 12, 2007 Report Share Posted September 12, 2007 I have flashed my i607 with the i600 new ROM and now I can't flash the phone back. The phone works because I haven't flashed this part, however had flashed the PDA and have no camera anymore, no vibrator, but at least a working O/S. I have tried the following: a ) Purchased the D820 cable. I can see the phone connected using Tera Term in COM1, however is not seen by the WCE downloader as this is looking at USB ports. b ) I have tried installing the modem drivers time and again, and tried to connect ActiveSync in COM1 according to these instructions: (1) Use a Samsung D820 cable with Serial Port and plug into your i60x (2) Connect the cable to your PC's serial port (probably COM1) (3) Install the Samsung Blackjack Modem Driver (4) Uncheck the "Allow USB connections" in Active Sync option and select COM1 in "Allow connections in one of the followings" (5) Let Active Sync to search for the i60x and wait for "Connected" (6) Run the i600 firmware update program as usual. NO results. ActiveSync does not connect. c ) Tried Corona Downloader ver 3.2 for Samsung SGH-D500, it connects to the phone, but vendor ID sent is 0x44 and the phone responds 0x52, aborting further exchanges. I also tried OneNAND downloaders ver 1.4, 1.7 and 1.8 with similar results. I know these flashers may not work on my phone, however gave ma an idea some exchange was taking place... d ) I tried to load the bootloader eboot.nbo in root of the SD card, however i don't know if there should be a key combination to boot from SD card or if there is one other trick nor what name the file should have. Any ideas here? e ) I have made dumps prior this mishap of all 4 raw partitions in the phone. Is it there a way to write a partition using a utility that I can place in the SD card? Is it there available a SD flasher that may run from the phone? f ) Is it there a way to modify the WCE downloader to work on COM1 instead of USB? g ) Is it there a way to modify the device driver to accept the phone as it is now? Apparently the phone device driver messages windows with a device malfunction and Device not recognized. Is it there any way to bypass this? h ) I even tried to use a Serial-USB bridge and WCE downloader. No results either. If you have any ideas, please respond to this thread. Any input will be deeply appreciated. Thank-you in advance. Link to comment Share on other sites More sharing options...
Guest kohala Posted September 19, 2007 Report Share Posted September 19, 2007 HAHA You knew the job was dangerous when you took it, Fred Link to comment Share on other sites More sharing options...
Guest trinca Posted September 24, 2007 Report Share Posted September 24, 2007 (edited) HAHA You knew the job was dangerous when you took it, Fred The thrill of finding a solution is worth all the trouble. Hachete, ave you tried UST pro? Mm, and on a second though, perhaps AT$T may flash it back using JTAG, you may take the phone to an AT$T $ervice Center, at this point what else you may loose?... Edited September 24, 2007 by trinca Link to comment Share on other sites More sharing options...
Guest scandalous Posted October 21, 2007 Report Share Posted October 21, 2007 I flashed my i607 with i600 Firmware too. I dont know how to reverse back to i607. I just sent an email to Samsung USA ask them how to do that. If I got any respond I'll post here. Link to comment Share on other sites More sharing options...
Guest David Sang Posted November 15, 2007 Report Share Posted November 15, 2007 I flashed my i607 with i600 Firmware too. I dont know how to reverse back to i607. I just sent an email to Samsung USA ask them how to do that. If I got any respond I'll post here. Could you please advise how is Samsung reply this case ? Thanks ! Link to comment Share on other sites More sharing options...
Guest AximMarkSD Posted January 16, 2008 Report Share Posted January 16, 2008 Anyone have any thoughts on this? I'm having similar issues w/ a cooked WM6 ROM. I can't get the PC to recognize the phone via Activesync or w/ the modem drivers. Thanks, Mark Link to comment Share on other sites More sharing options...
Guest Feke Posted April 8, 2008 Report Share Posted April 8, 2008 Ehh. I've got the same problem. but the difference is, that the one who killed the phone wasn't me, it was an earlier owner of the device. to solve the problem I bought an i600(realy!) so maybe it's active sync cd and its sw will be good for my bj, but it wasn't. The pc couldn't find my phone, not as an i607 and not as an i600.. so I couldn't reflash it to i607. :( if is there anyone who could help me with this, please e-mail me to: [email protected] (I didn't miswrote it, this is my mail adress). I've sent an e-mail to samsung, but they wrote, that: "It always causes problems if you take a phone from a country to another one wich uses diferent bandwiths." ?????? I don't understand... i wrote, that it has been flashed with i600 rom, and asked, that is there any way to repair it here in Hungary?... Link to comment Share on other sites More sharing options...
Guest glucklichstas Posted December 3, 2008 Report Share Posted December 3, 2008 Sorry if this question has been asked in the forum, nemogli would you suggest I might install wm6 with a memory card on the i600? if so, what combination keypad? and another question: people who set on i6a0 rom from the i607, as you have your phone repaired? I have it just as you do not include ((((( look forward to your help) B) Link to comment Share on other sites More sharing options...
Guest jet24 Posted January 27, 2011 Report Share Posted January 27, 2011 Hi everyone I know this post is old and I have the same problem, I figured out the solution but don't know how to do it, I know that if we get a working i607 eboot.nb0(bootloader), we can run it from sd card with JumpSPL if we manage to get the jump adress of the i607 ,then with the working bootloader we can install an i607 eboot/pda/phone rom from pc . Here's a link on how to do that: http://forum.xda-developers.com/showthread.php?t=334667 But I don't do it because I don't have any programming knowledge, so if someone is able to do it, please help.JumpSPLv1.zip Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now