Omnia dead after try to do the upgrade.

[Guest Andre Heitor]

I was using Octans 2.14 to update my Omnia II i8000 to i8000nxxje1.

Gave a mistake in the update, now the phone does not power on, only the icon appears of the battery loading.

Octans does not recognize anymore the phone.

I already tried hard reset.

Help me!!!

[Guest plguzman]

Could be more specific in what "mistake" you made? More information about that could be helpful.

[Guest Dj_suca]

I was using Octans 2.14 to update my Omnia II i8000 to i8000nxxje1.

Gave a mistake in the update, now the phone does not power on, only the icon appears of the battery loading.

Octans does not recognize anymore the phone.

I already tried hard reset.

Help me!!!

flash back to your old Rom... so see if it fixes your problem...

[Guest MenosOcho]

I was using Octans 2.14 to update my Omnia II i8000 to i8000nxxje1.

Gave a mistake in the update, now the phone does not power on, only the icon appears of the battery loading.

Octans does not recognize anymore the phone.

I already tried hard reset.

Help me!!!

1° : try hard reset

2° : verify that you have the proper drivers for your OS and that you have disabled driver enforcement, disable too AV and Firewall

3° : flash again, remember connect the phone when it's off and wait until Octans say "done", never disconnect before that msg.

[Guest johnchua55]

remember to click detect button in octans ... then connect your phone ( your phone must be OFF )

[Guest Andre Heitor]

I disconnected before the message DONE.

I already had done several upgrades, but this time I disconnected the phone before concluding.

I already tried hardreset, but without success.

Octans does not recognize the phone.

[Guest moxadrian]

I disconnected before the message DONE.

I already had done several upgrades, but this time I disconnected the phone before concluding.

I already tried hardreset, but without success.

Octans does not recognize the phone.

what is happening when the phone is off and conected to computer?

[Guest Mr. WonderFULL]

what is happening when the phone is off and conected to computer?

Battery Charging :rolleyes: if using octans the device entering download mode

[Guest Terry666]

I disconnected before the message DONE.

I already had done several upgrades, but this time I disconnected the phone before concluding.

I already tried hardreset, but without success.

Octans does not recognize the phone.

Does the battery is full or at least 60% or more? If NOT, charge it OUTSIDE the phone, if you don't have charger do it IN the phone and after charging for 1-2 hours take the battery OFF the phone for at least 10 minutes.

Re-insert battery and try H/R and if not good then try flash a FULL ROM...

I hope it help you.

GOOD LUCK friend :rolleyes:

[Guest Hiroshi.Rio]

Andre, já tentou deixar selecionado o "Step 2: Detect the device: Start downloading immediately" no OCTANS 2.14?

Não tem problema em desconectar o aparelho antes de terminar o upgrade. Eu já fiz isso também e tá tudo funcionando.

Ah, e outra: não use cabo extensor para conectar o Omnia ao PC.

Veja aí se funciona e posta os resultados. :rolleyes:

_____

Did you select "Step 2: Detect the device: Start downloading immediately" on OCTANS 2.14?

Do not use a cable extensor to connect the device to PC.

Post the results. :D

[Guest johnchua55]

Battery Charging biggrin.gif if using octans the device entering download mode

seems your phone is not dead yet. flash it again ...... run octans choose your PDA (MST/nbo) ..... click detect .... then connect your phone..... click start downloading

[Guest darychia]

I was using Octans 2.14 to update my Omnia II i8000 to i8000nxxje1.

Gave a mistake in the update, now the phone does not power on, only the icon appears of the battery loading.

Octans does not recognize anymore the phone.

I already tried hard reset.

Help me!!!

It happen to me before, just took out the battery and insert it back, re-flash again. It works for me, sometimes I even stop halfway cause I notice that I have used the wrong one,

I unplug the usb and took out the battery and insert it back, re-flash again after I had confirmed that I choose the right one, it still work for me without any issue. hoep it do work for

you. Cheers. :(

[Guest darychia]

I was using Octans 2.14 to update my Omnia II i8000 to i8000nxxje1.

Gave a mistake in the update, now the phone does not power on, only the icon appears of the battery loading.

Octans does not recognize anymore the phone.

I already tried hard reset.

Help me!!!

It happen to me before, just took out the battery and insert it back, re-flash again. It works for me, sometimes I even stop halfway cause I notice that I have used the wrong one,

I unplug the usb and took out the battery and insert it back, re-flash again after I had confirmed that I choose the right one, it still work for me without any issue. hoep it do works for

you. Cheers. :(

[Guest darychia]

I was using Octans 2.14 to update my Omnia II i8000 to i8000nxxje1.

Gave a mistake in the update, now the phone does not power on, only the icon appears of the battery loading.

Octans does not recognize anymore the phone.

I already tried hard reset.

Help me!!!

It happen to me before, just took out the battery and insert it back, re-flash again. It works for me, sometimes I even stop halfway cause I notice that I have used the wrong one,

I unplug the usb and took out the battery and insert it back, re-flash again after I had confirmed that I choose the right one, it still work for me without any issue. hope it do works for

you. Cheers. :(

Edited May 28, 2010 by darychia