is there a wifi router app for omnia 2 i8000?

[Guest nutpantz]

ive been looking for a wifi router app for the i8000

something that would make my phone into a wifi router..

i have only found wm 6.1 apps

can any one point me at something that works for the omnia i8000

[Guest wuzzy]

Here you go...

(Mobile AP from Samsung)

http://www.modaco.com/index.php?act=attach...st&id=57247

Edited December 11, 2010 by wuzzy

[Guest alexovy]

wmwifirouter

[Guest turnado1979]

ive been looking for a wifi router app for the i8000

something that would make my phone into a wifi router..

i have only found wm 6.1 apps

can any one point me at something that works for the omnia i8000

find below link for wmwifirouter

http://www.mediafire.com/?f9ugk3abcqsy358

Edited December 14, 2010 by turnado1979

[Guest Alex K.S.Lim]

Haven't try the Mobile AP.

But WMWifiRounter working just fine with my Omnia 2 I8000.

[Guest bobhero]

Anyone else using Mobile AP?

I am getting very poor speeds with it. When I USB tether I get between 3-6Mbps down. When I use Mobile AP over wifi, I can only get a pathetic 0.6Mbps down.

I tried disabling encryption, and plugging the phone into the wall power, but it made no difference. As soon as I closed the program and started USB tethering again, the speeds wither back to 3-6Mbps down, so it is not the network. To be sure, I immediately switched back and tried Wifi again, and I got the same poor speeds.

I also doubt it is the wifi connection, I monitor the link and it stays at 54Mbps the entire time, also the phone and the laptop are only 10cm apart. And when I test the laptop's wifi on my broadband connection, it can easily do 10+mbps.

I just tested with WMWifiRounter and I am able to get full speeds the same as USB tethering. I'd rather use Mobile AP, because of the black theme.

Any ideas why Moblie AP is lagging so far behind?

Edited December 28, 2010 by bobhero

[Guest erieboatergal]

I was looking for a solution to connect my nook color to my Samsung Omnia 2 via Wifi. I downloaded WMWifiRouter to set up an ad hoc wifi network. I also downloaded Intshrui, to ensure i had internet sharing on my phone. Everything seems to work correctly, and I am connected to the internet on my phone, but I can't see the connection on my nook. On the front page of WMWifiRouter, it says it is ready, and under Cellular, it says broadband access connected. I can also see the network name and the WEP password that I put in. When I go to the overview page, I am getting these readings:

Inbound Outbound

Cellular 0B/s 0B/s

5.3MB 532.8 KB

Wi-Fi 0B/s 0B/s

0B 0B

I know it has something to do with the above numbers being 0, but I don't know what it is. I've read that this is the easiest program to use, and am hoping that it is an easy solution. I have searched this forum, the FAQ and Documentation on the WMWifiRouter page, and XDA and have not found a solution to my specific problem.

Thank you for your response.

erieboatergal

[Guest rgsekula]

It has to do with android's inability to tether as a client to an ad-hoc network. in fact it wont even display the network in the connections settings.

I can not connect my Dell Streak/ Froyo 2.2 to my phone either. neither thru wi fi or thru BT Pan. I can connect/ tether my mac both ways fine however.

On 2.1- With Root - one could play with the sys/bin/wpa_supplicant ; doing so let me see the network. Then I would set a static IP and could connect to the WMWiFi network but not to the internet.

However if i create a network/hotspot on my wifes Palm Pre i can connect fine.

If someone can help me figure out how to tether my Streak (as a Client) to my Omnia2 I would be very grateful.

Is there anyway to create a wifi hotspot that is not an ad-hoc network? i would love to be able to tether via BT but android does not yet have the infrastructure.

I was looking for a solution to connect my nook color to my Samsung Omnia 2 via Wifi. I downloaded WMWifiRouter to set up an ad hoc wifi network. I also downloaded Intshrui, to ensure i had internet sharing on my phone. Everything seems to work correctly, and I am connected to the internet on my phone, but I can't see the connection on my nook. On the front page of WMWifiRouter, it says it is ready, and under Cellular, it says broadband access connected. I can also see the network name and the WEP password that I put in. When I go to the overview page, I am getting these readings:

Inbound Outbound

Cellular 0B/s 0B/s

5.3MB 532.8 KB

Wi-Fi 0B/s 0B/s

0B 0B

I know it has something to do with the above numbers being 0, but I don't know what it is. I've read that this is the easiest program to use, and am hoping that it is an easy solution. I have searched this forum, the FAQ and Documentation on the WMWifiRouter page, and XDA and have not found a solution to my specific problem.

Thank you for your response.

erieboatergal

Edited January 2, 2011 by rgsekula

[Guest sixx07]

i just lil bit worry using the O2 as wifirouter. it's so HOT after a mature of minutes. are you guys convinience with the temperature of this device while tethering? i just afraid i will break it up.......

[Guest bobhero]

i just lil bit worry using the O2 as wifirouter. it's so HOT after a mature of minutes. are you guys convinience with the temperature of this device while tethering? i just afraid i will break it up.......

I turn off the screen, it helps, but it does get warm on USB tether and hot with wifi tether.