Jump to content

[STOPPED] CyanogenMod Beta2 Omnia 2 (updated: 04.05.2012)


Guest voyteckst
 Share

Recommended Posts

What do you mean?

I'm talking about MY STORAGE PARTITION not MY DEVICE partition.

Even if you erase your MyStorage WinMo will work fine, but you LOST all your programs and files that was installed in My Storage.

But like i said, i don't want to do that. No time for backup now, will try to install into SD CARD.

Uhm...

got it... soo, good bye to My Storage, then, repartition it with My Storage back and ext4...?

Link to comment
Share on other sites

Go to init.rc and add this iocharset=utf8 after your MyStorage mount command line, like this:

mount vfat /dev/block/mmcblk0p5 /storage iocharset=utf8

That did the trick! Thanks a lot!

Link to comment
Share on other sites

Uhm...

got it... soo, good bye to My Storage, then, repartition it with My Storage back and ext4...?

You have to know what you are doing, just wait a little bit more.

Link to comment
Share on other sites

Read the README:

Note: mmcblk0 is now SD card, mmcblk1 is My Storage.

Dev. Team can wrong too.

I write true teory.

I installed now in my SECOND PRIMARY PARTITION on My Storage and is mmcblk0p2, My FIRST PRIMARY PARTITION in WINMO is still mmcblk0p1. is TRUE

Link to comment
Share on other sites

Dev. Team can wrong too.

I write true teory.

I installed now in my SECOND PRIMARY PARTITION on My Storage and is mmcblk0p2, My FIRST PRIMARY PARTITION in WINMO is still mmcblk0p1. is TRUE

however, i install it in my sd card and is mmcblk0p2 working too :)

Link to comment
Share on other sites

Dev. Team can wrong too.

I write true teory.

I installed now in my SECOND PRIMARY PARTITION on My Storage and is mmcblk0p2, My FIRST PRIMARY PARTITION in WINMO is still mmcblk0p1. is TRUE

Read carefully. mmcblk1 means only whole disk. You have to add p(number)

mmcblk0 means whole sdcard and mmcblk0p1 means its first partition.

Edited by voyteckst
Link to comment
Share on other sites

Read carefully. mmcblk1 means only whole disk. You have to add p(number)

mmcblk0 means whole sdcard and mmcblk0p1 means its first partition.

Since the partition is set right. I`m going to rebuild all my Storage partition table, cuse just can`t get out of Android logo, just load and load....

fsck also says that the partition got a problem, but can`t fix it.

Edited by rom_omnia2
Link to comment
Share on other sites

Ok guys. I tested it one more time. WiFi works like charm. Tell me how You installed it.

So mine WIFI doesn't work and heres how i installed it:

1, Extracted the package

2, created an ext4 partition via gparted in ubuntu

3, copyied the tar.gz file to the ext4 partition

4, extracted the file and deleted it

5, put haret zimage and startup file to my storage

6, Started haret

7, everythin works fine except the wifi

What should i do reinstall?

Link to comment
Share on other sites

For those with wifi problem. Please try to increase screen timout to 2 minutes. Additionally enable adb and send me logcat output from enabling wifi.

Please remember about wifi sleep bug.

Link to comment
Share on other sites

For those with wifi problem. Please try to increase screen timout to 2 minutes. Additionally enable adb and send me logcat output from enabling wifi.

Please remember about wifi sleep bug.

I know about sleep + wifi bug, but i tried restart several times, but doesn't work...

Link to comment
Share on other sites

I know about sleep + wifi bug, but i tried restart several times, but doesn't work...

Run adb logcat from pc, try to enable wifi and send output (piece with wifi part).

Link to comment
Share on other sites

For me is imposible to recognize the partition... Still on pink screen. Funny that with the last version worked fine.

Something i could do?

With me this happens accurately.

I am using My Storage with EXT4 and runs the following one

Set kernel zImage

Set ramsize 180*1024*1024

Set mtype 1626

Set ramaddr 0x50000000

Set kernelcrc 1

Set CMDLINE "rootdelay=2 root=/dev/mmcblk1p2 init=/init"

boot

Exists something wrong???

Link to comment
Share on other sites

installed on mystorage with ext4 and everything works fine including wifi

but after using it for couple of minutes, the phone gets so sloooooooooow

i'll try to figure out the solution to this problem...

thx devs for your hard work!

edit: the problem was the market. it takes about 16M memory. but even with market turned off, it only leaves me with around 20M memory...

Edited by haebinlim
Link to comment
Share on other sites

Run adb logcat from pc, try to enable wifi and send output (piece with wifi part).

Ok i got adblogcat but i don't have the driver for the phone... I tried to install google adb drivers but the pc says that couldn't find proper drivers

Link to comment
Share on other sites

With me this happens accurately.

I am using My Storage with EXT4 and runs the following one

Set kernel zImage

Set ramsize 180*1024*1024

Set mtype 1626

Set ramaddr 0x50000000

Set kernelcrc 1

Set CMDLINE "rootdelay=2 root=/dev/mmcblk1p2 init=/init"

boot

Exists something wrong???

SD Card or My Storage?

If you are in Linux run this command:

fdisk -l

And post here the result.

Link to comment
Share on other sites

SD Card or My Storage?

If you are in Linux run this command:

fdisk -l

And post here the result.

My Storage

Device Boot Start End Blocks Id System

/dev/sdc1 1 808 6490228+ b W95 FAT32

/dev/sdc2 809 999 1534207+ f W95 Ext'd (LBA)

/dev/sdc5 809 999 1534176 83 Linux

Edited by Thor2
Link to comment
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
 Share

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.