Guest Amphoras Posted February 18, 2012 Report Posted February 18, 2012 no i can't get in fastboot because my pc cannot recognise my usb...and i have a orange san francisco(zte blade)gen 2...what can i do???i need to go to orange...they will fix it or my beloved zte blade died forever:(((((??? If its still under warranty you could try phoning Orange and see if they will replace it if you bought it from them. If you bought it second hand, then you'll probably have to go through whoever you bought it from, if you have a warranty. What happens if you hold the volume down button while turning it on? You could try working through the steps in the de-bricking thread and see if one of them works for you. Take it slowly and read each one carefully before trying it. Make sure you have the proper drivers installed first as well so your computer can recognise your phone.
Guest Davidoff59 Posted February 18, 2012 Report Posted February 18, 2012 Zteblade07 tried flashing a Gen 1 rom on a stock Gen 2 device if that helps. A couple of us gave as much help as we could. android.modaco.com/topic/351740-need-urgent-help/
Guest ZTE BLADE07 Posted February 18, 2012 Report Posted February 18, 2012 If its still under warranty you could try phoning Orange and see if they will replace it if you bought it from them. If you bought it second hand, then you'll probably have to go through whoever you bought it from, if you have a warranty. What happens if you hold the volume down button while turning it on? You could try working through the steps in the de-bricking thread and see if one of them works for you. Take it slowly and read each one carefully before trying it. Make sure you have the proper drivers installed first as well so your computer can recognise your phone. i bought the phone from orange abot 3 months ago...it is stiil under warranty but when i've done root it is not suposely to lose the warranty???and if a hold the volume down while turning appears the green android...so i can't acces clockwork even i am holding down for 5 min
Guest Amphoras Posted February 18, 2012 Report Posted February 18, 2012 i bought the phone from orange abot 3 months ago...it is stiil under warranty but when i've done root it is not suposely to lose the warranty???and if a hold the volume down while turning appears the green android...so i can't acces clockwork even i am holding down for 5 min Try the methods in the de-bricking thread. One of them might work for you.
Guest ZTE BLADE07 Posted February 18, 2012 Report Posted February 18, 2012 Try the methods in the de-bricking thread. One of them might work for you. i've tried the third method and when i turn on with menu and vol+ hold down appears a green test:UPDATE FROM T-FLASH CARD and below many "errors"...the first method is to acces the clockwork and i can't,the second is to acces the phone via usb but my computer says USB DEVICE CANNOT BE RECOGNISED tha fourth the same requesting to boot in to recovery again i can't and the last methos it seems to me too dangerous of losing my blade forever...
Guest Amphoras Posted February 19, 2012 Report Posted February 19, 2012 i've tried the third method and when i turn on with menu and vol+ hold down appears a green test:UPDATE FROM T-FLASH CARD and below many "errors"...the first method is to acces the clockwork and i can't,the second is to acces the phone via usb but my computer says USB DEVICE CANNOT BE RECOGNISED tha fourth the same requesting to boot in to recovery again i can't and the last methos it seems to me too dangerous of losing my blade forever... If none of them will work then your only option is to phone Orange and try and get it replaced.
Guest ZTE BLADE07 Posted February 19, 2012 Report Posted February 19, 2012 If none of them will work then your only option is to phone Orange and try and get it replaced. I will go to orange shop and hope they will receive it...anyway tnk a lot
Guest himanshu xcd35 Posted February 23, 2012 Report Posted February 23, 2012 Guys..i tried to do a TPT of my stock gen 2 dell blade. It rebooted just fine and i saw the error screen in green fonts as mentioned but it didnt moved ahead of that screen. what can be the problem?
Guest Amphoras Posted February 24, 2012 Report Posted February 24, 2012 Guys..i tried to do a TPT of my stock gen 2 dell blade. It rebooted just fine and i saw the error screen in green fonts as mentioned but it didnt moved ahead of that screen. what can be the problem? Did you check the md5sums before starting? What does it show now? The green android, black screen, etc.?
Guest himanshu xcd35 Posted February 24, 2012 Report Posted February 24, 2012 Did you check the md5sums before starting? What does it show now? The green android, black screen, etc.? Hi Amphoras, I didnt checked the MD5sums... you will laugh but actually i dont know how to check that.. and after rebooting..it was all black and in green colour there was one line written abut the team i suppose.. then in next 5-6 lines it was just written Error! Error! Error! Error! then i took battery out and started my phone normally...it was working fine.. So luckily nothing bad happened...but i want to run the tpt in order to unlock ram if available.
Guest ZTE BLADE07 Posted February 24, 2012 Report Posted February 24, 2012 Hi Amphoras, I didnt checked the MD5sums... you will laugh but actually i dont know how to check that.. and after rebooting..it was all black and in green colour there was one line written abut the team i suppose.. then in next 5-6 lines it was just written Error! Error! Error! Error! then i took battery out and started my phone normally...it was working fine.. So luckily nothing bad happened...but i want to run the tpt in order to unlock ram if available. himanshu you are a lucky man:))...to check the md5 you need(astro file manager just an ex)or i personally use MD5 Checksum Verifier...this is a program from my PC...and if yoy have a gen2 phone this mean you don't need to unlock extra ram because gen2 phones already have 512 ram...
Guest Decadence1 Posted February 24, 2012 Report Posted February 24, 2012 (edited) Hi, I've followed the instructions in the original post but when I press +vol and menu, nothing happens and the phone just boots as normal. What am I doing wrong? EDIT: never mind got it Edited February 24, 2012 by Decadence1
Guest Amphoras Posted February 24, 2012 Report Posted February 24, 2012 Hi Amphoras, I didnt checked the MD5sums... you will laugh but actually i dont know how to check that.. and after rebooting..it was all black and in green colour there was one line written abut the team i suppose.. then in next 5-6 lines it was just written Error! Error! Error! Error! then i took battery out and started my phone normally...it was working fine.. So luckily nothing bad happened...but i want to run the tpt in order to unlock ram if available. You should always check the md5sums. If the file has been corrupted during downloading/unzipping and you flash it, it could permanently brick your phone. You can use a few apps from the market to check md5sums. There is AFV, or you can use TPT Helper which is designed for this stuff. There seem to be a few Blades just getting the list of errors when trying to use these. When I have the time I will try and look into it and find out why it happens. It doesn't seem to actually flash anything, so its probably not likely to cause any damage.
Guest JimJam707 Posted February 24, 2012 Report Posted February 24, 2012 Hey guys, I am trying to flash a TPT from the first post, but holding down Vol+ and Power just boots up the device normally :/
Guest Amphoras Posted February 25, 2012 Report Posted February 25, 2012 Hey guys, I am trying to flash a TPT from the first post, but holding down Vol+ and Power just boots up the device normally :/ Was your phone originally Gen 1? If so then you probably need to use a Gen 1 to Gen 2 type TPT.
Guest JimJam707 Posted February 25, 2012 Report Posted February 25, 2012 Was your phone originally Gen 1? If so then you probably need to use a Gen 1 to Gen 2 type TPT. It was, so that explains that. Thanks :)
Guest epyloxias Posted February 25, 2012 Report Posted February 25, 2012 (edited) Which one of the 3 listed partitions is the most suitable for coldfusion? I kinda confused a little bit.... :blink: My phone was Gen 1 and I used Gen 1 to Gen 2 type TPT. Is it enough for coldfusion? Edited February 25, 2012 by epyloxias
Guest De@n Posted February 25, 2012 Report Posted February 25, 2012 (edited) Which one of the 3 listed partitions is the most suitable for coldfusion? I kinda confused a little bit.... :blink: My phone was Gen 1 and I used Gen 1 to Gen 2 type TPT. Is it enough for coldfusion? Gen1-to-Gen2-TPT-v10-stock.zip MD5:ae0207cd88429a062d8b1770b3acd2c4 This one. Edited February 25, 2012 by De@n
Guest ZTE BLADE07 Posted February 25, 2012 Report Posted February 25, 2012 You should always check the md5sums. If the file has been corrupted during downloading/unzipping and you flash it, it could permanently brick your phone. You can use a few apps from the market to check md5sums. There is AFV, or you can use TPT Helper which is designed for this stuff. There seem to be a few Blades just getting the list of errors when trying to use these. When I have the time I will try and look into it and find out why it happens. It doesn't seem to actually flash anything, so its probably not likely to cause any damage. amphoras i get the same error when i try to TPT the phone...i finally gave up and i was to orange...but if you have time please do some research why this ërrors"occurs
Guest n3tk0 Posted February 25, 2012 Report Posted February 25, 2012 (edited) Hey guys, I have a problem, Yesterday when I try to resize my layout, I faced up with a problem. I make all steps, return the original recovery and all other files was at the phone, but when I try to with flasher my phone disconnect at 6/100 and at 8/100 the program say FAIL. Ok, my phone boot up like nothing was change. I try also with TPT Helper, and other images with stock rom on them, I still face the problem, there is no status bar for showing a progress for installation... I stuck with 160MB system Layout... made with flasher... Please give me some advice to get out from the situation. Thank you. PP: I forgot my phone is stock GEN 2. Edited February 25, 2012 by n3tk0
Guest Amphoras Posted February 25, 2012 Report Posted February 25, 2012 Which one of the 3 listed partitions is the most suitable for coldfusion? I kinda confused a little bit.... :blink: My phone was Gen 1 and I used Gen 1 to Gen 2 type TPT. Is it enough for coldfusion? You can use the ones from here. Hey guys, I have a problem, Yesterday when I try to resize my layout, I faced up with a problem. I make all steps, return the original recovery and all other files was at the phone, but when I try to with flasher my phone disconnect at 6/100 and at 8/100 the program say FAIL. Ok, my phone boot up like nothing was change. I try also with TPT Helper, and other images with stock rom on them, I still face the problem, there is no status bar for showing a progress for installation... I stuck with 160MB system Layout... made with flasher... Please give me some advice to get out from the situation. Thank you. PP: I forgot my phone is stock GEN 2. Try one of the Gen 1 to Gen 2 type TPTs from here. Depending on what package you used with the Windows flasher you need different types.
Guest n3tk0 Posted February 25, 2012 Report Posted February 25, 2012 Try one of the Gen 1 to Gen 2 type TPTs from here. Depending on what package you used with the Windows flasher you need different types.
Guest epyloxias Posted February 25, 2012 Report Posted February 25, 2012 (edited) Gen1-to-Gen2-TPT-v10-stock.zip MD5:ae0207cd88429a062d8b1770b3acd2c4 This one. uh..... nope! That didn't worked for me :unsure: Edited February 25, 2012 by epyloxias
Guest Amphoras Posted February 25, 2012 Report Posted February 25, 2012 Thank you that help, but the question I have is now which version is my phone? And what was the problem. If the ones from that link worked, then I guess you used a Gen 1 to Gen 2 type layout when you first used the Windows flasher. This means you need to use Gen 1 to Gen 2 type TPTs. Your phone should still be Gen 2, but you can check with Mr Pigfish if you want. I don't know why the flasher wasn't working for you though.
Guest De@n Posted February 25, 2012 Report Posted February 25, 2012 uh..... nope! That didn't worked for me :unsure: You followed Amphoras' instructions on page 1?
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now