[KERNEL] TechnoLover's Kernel Edition 1.5 (25.06.2012)

[Guest chemicalbuz]

where do you look for battery bar? in notification bar or in settings?

lagfree reduces the frequency when the load is under a specific percentage, so maybe the load is at 368 MHz not low enough? When screen off, it should go down to 122 MHz ;)

i mean in the top bar, i didn't check in battery stats :) ok no problem about underclock, just to know ;)

today I'm gonna release new version I was too tired yesterday

will it be compatible with new 2.3.6 update?

Edited November 4, 2011 by chemicalbuz

[Guest TropicalRooster]

Thanks a lot for your hard work.

[Guest dads]

wifi not work in 2.3.6

[Guest TechnoLover]

Kernel will be published 2-3 days later, because of stock 2.3.6, GignerOunay 3.0, new recovery and some bugs (:

[Guest stoorzsto]

Kernel will be published 2-3 days later, because of stock 2.3.6, GignerOunay 3.0, new recovery and some bugs (:

I'm using your kernel with Gingerounay 3.0 without any question.:)

Wifi working as well.

Edited November 5, 2011 by stoorzsto

[Guest mjpgly]

Kernel will be published 2-3 days later, because of stock 2.3.6, GignerOunay 3.0, new recovery and some bugs (:

your Kernel working perfect,thanks,waiting for low voltage edition

Edited November 7, 2011 by mjpgly

[Guest mjpgly]

I'm using your kernel with Gingerounay 3.0 without any question.:)

Wifi working as well.

i tried flash this kernel with Gingerounay3.0,but can't boot......

i checked script,found app2sd script conflict with this kernel

Edited November 7, 2011 by mjpgly

[Guest mlk75]

I am using this kernel with Gingerounay3.0. No issue except, phone get little warm.. and drain battery quite fast. Also seems charging is slower than usual.

Edited November 7, 2011 by mlk75

[Guest TechnoLover]

Update (:

check first post (:

Edited November 7, 2011 by TechnoLover

[Guest stonebear]

Thanks Techno.

Can I ask what is stock Acer mV?

Is it 1100mV?

.

Edited November 7, 2011 by stonebear

[Guest TechnoLover]

900/900/900/1050/1100/1200/1200/1250/1300/1350 - normally they should be displayed in MT Voltage Control app, because you shouldn't have any undervolt ;)

[Guest stonebear]

900/900/900/1050/1100/1200/1200/1250/1300/1350 - normally they should be displayed in MT Voltage Control app, because you shouldn't have any undervolt ;)

So, if I select 806@1100mV (for example) that is stock, then I can choose lower mV and will be undervolting?

I then set mV for each individual frequency that the processor will use? 122, 245, 368 etc? Not like setting a maximum vcore and the OS decides vcore for all the frequencies based on that maximium.

.

Edited November 7, 2011 by stonebear

[Guest TechnoLover]

yes, that's the way - be sure you test every frequency with chosen voltage.

yes, you can set voltage for every frequency. When you have done everything, you can save them for boot.

[Guest stonebear]

yes, that's the way - be sure you test every frequency with chosen voltage.

yes, you can set voltage for every frequency. When you have done everything, you can save them for boot.

I understand now, thanks.

[Guest spal]

Update (:

check first post (:

It's awesome!

That's what I waiting for a looooong time --UV from OS-- Great work TechnoLover!

Thank You very much!

[Guest Torstiko]

Hi

I'm using dmd with the low voltage kernel. How do i know wich settings to make in the new kernel?

Are there presets?

Thanks

Torstiko

[Guest TechnoLover]

No, there aren't any presets, I don't know the voltages from dmd, but you can have a view on my voltages on the first post, you see them on the screenshot. They are very low, so keep them a bit higher and try to lower them each for a bit ;)

[Guest Torstiko]

Thanks Technolover,

If i flash your kernel, are there still the current settings or the stock ones?

Greets

Torstiko

[Guest TechnoLover]

stock voltage

[Guest spal]

After I saved my settings and do a reboot, at the first start, the program still shows the reference --stock-- voltages. Is it's just the app's starting value or it does a reading at start and the save was unsuccessful?

[Guest TechnoLover]

please tell me your rom and I'll have a look ;)

yes it means it was unsuccessful in loading or saving them :/

Edited November 7, 2011 by TechnoLover

[Guest edisson77]

please tell me your rom and I'll have a look ;)

yes it means it was unsuccessful in loading or saving them :/

I have same problem. After rebooting, MT Voltage Control shows stock value.

Official ROM 4.000.13 GEN1 with RecoveryMT 2.2, Root, your last kernel.

[Guest wmj1983]

qiang lie zhi chi xia

[Guest mjpgly]

i really like this kernel,so I flash new kernel on Gingerounay3.0,but apps2sd still can't work ,no /sd-ext

and some tweak lost,like /sys/devices/virtual/bdi/179:0/read_ahead_kb,Gingerounay3 is echo 1040

Edited November 8, 2011 by mjpgly

[Guest stonebear]

I flash this new kernel on Gingerounay3.0,apps2sd still have problem,no /sd-ext

I don't think the kernel would affect that? Not that I know anything about this stuff.

Edited November 8, 2011 by stonebear