Guest Inf3cted Posted November 13, 2011 Report Share Posted November 13, 2011 (edited) Hi! I started install CM Nightly and after that phone bricked? Now looking solutions and dosnt find anythink. The phone only black screen. If i turn it on, only red light working 3 seconds. Sometime working Vibration when press power button. Maybe someone can help? Sry for bad English, i hope you understand what i want to say. Now the phone is working, but black screen only. If i press power button then home/menu/back button light up and pressing power button again then lights dosnt work. Volume button work, i can hear sound. If i connect USB cable, computer not finding phone and if i remove USB then phone making voice. Maybe any solutions? Edited November 13, 2011 by Inf3cted Link to comment Share on other sites More sharing options...
Guest Arnar Posted November 13, 2011 Report Share Posted November 13, 2011 Can you boot into recovery? holding Power button + volume down... Link to comment Share on other sites More sharing options...
Guest Inf3cted Posted November 13, 2011 Report Share Posted November 13, 2011 Can you boot into recovery? holding Power button + volume down... CAnt boot recovery mode. Link to comment Share on other sites More sharing options...
Guest swukjay Posted November 13, 2011 Report Share Posted November 13, 2011 Hi! I started install CM Nightly and after that phone bricked? Now looking solutions and dosnt find anythink. The phone only black screen. If i turn it on, only red light working 3 seconds. Sometime working Vibration when press power button. Maybe someone can help? Sry for bad English, i hope you understand what i want to say. Now the phone is working, but black screen only. If i press power button then home/menu/back button light up and pressing power button again then lights dosnt work. Volume button work, i can hear sound. If i connect USB cable, computer not finding phone and if i remove USB then phone making voice. Maybe any solutions? use TPT to recover then reflash rom tpt is fail safe way to restore and a great format tool ! Link to comment Share on other sites More sharing options...
Guest hugobosslives Posted November 13, 2011 Report Share Posted November 13, 2011 you have two options: either: 1) try to flash a new recovery with fastboot and see if that boots. then reflash cm7 or 2) flash a tpt. your choice :D btw, describe what you did to screw it up. this will help Link to comment Share on other sites More sharing options...
Guest Inf3cted Posted November 13, 2011 Report Share Posted November 13, 2011 (edited) use TPT to recover then reflash rom tpt is fail safe way to restore and a great format tool ! How i recover with TPT if i cant get connected with computer. you have two options: either: 1) try to flash a new recovery with fastboot and see if that boots. then reflash cm7 or 2) flash a tpt. your choice :D btw, describe what you did to screw it up. this will help I cant connect ZTE with Computer. Fastboot woking only if i connect mobile and computer together right? Maybe u can give me tips how i can do that? I didnt do anythink, today i get that from friend. I have only black screen and charging light is red. If i press power button then phone working, only black screen. Edited November 13, 2011 by Inf3cted Link to comment Share on other sites More sharing options...
Guest martin tander(estonia) Posted November 13, 2011 Report Share Posted November 13, 2011 Get a card reader or device that supports ur sd...then download a TPT file unzip in /sd and put sd in ur blade back(there must be folder called image) then power up holding vol up+menu wait till green txt finishes his thing then boot into recovery and flash rom u want to flash(u can find TPT with integrated rom in it) Link to comment Share on other sites More sharing options...
Guest hedgepigdaniel Posted November 14, 2011 Report Share Posted November 14, 2011 First, remove the battttery, put it back in, and charge it for a few hours. Link to comment Share on other sites More sharing options...
Guest Inf3cted Posted November 14, 2011 Report Share Posted November 14, 2011 I have antoher phone when i can put sdcard and isert files on SD card root. i open image files and put all files on the root. not image folder right? Then i put sdcard to ZTE blade and holding down power button/volume/home buttons. REd light is on like 5sec in 15seconds vibrate sarting work. then im waited like 5min. nothing on the screen, only black. If i press power button then lights up home/menu/back buttons. bressing again power button then lights dosn work. And charged phone few hours. Link to comment Share on other sites More sharing options...
Guest martin tander(estonia) Posted November 14, 2011 Report Share Posted November 14, 2011 (edited) Ok he tried but phone wouldnt go in dl mode(led not flashing) and still pc not seeing it... tpt not working either he tried few times... But if he gets led working for few seconds its not fully dead,right? Edited November 14, 2011 by martin tander(estonia) Link to comment Share on other sites More sharing options...
Guest Chris Banks Posted November 14, 2011 Report Share Posted November 14, 2011 (edited) i open image files and put all files on the root. not image folder right? No, you unzip the TPT zip file to your SD card. So there should be a folder called image on it. Then i put sdcard to ZTE blade and holding down power button/volume/home buttons. Put your SD card back in, press and hold VOLUME UP and MENU when turning on. Wait, Some green writing should come up, Wait, and then clockworkmod loads. Then you flash your ROM. Edited November 14, 2011 by Chris Banks Link to comment Share on other sites More sharing options...
Guest Inf3cted Posted November 14, 2011 Report Share Posted November 14, 2011 (edited) No, you unzip the TPT zip file to your SD card. So there should be a folder called image on it. Put your SD card back in, press and hold VOLUME UP and MENU when turning on. Wait, Some green writing should come up, Wait, and then clockworkmod loads. Then you flash your ROM. I done that all. But nothing,. We here trying with user Martin Tander on MSN and he give me tips. But nothing work. I pot image faile into sd card. Holding down volume + button/menu button and turning on. Red light working few seconds and thats it. I have waited 10min but nothing. Then i remove sd card and battety, then insert battery and turning on. Nothink. I think its dead? Edited November 14, 2011 by Inf3cted Link to comment Share on other sites More sharing options...
Guest unrandomsam Posted November 14, 2011 Report Share Posted November 14, 2011 When you say you have tried download mode. You mean with the battery removed - holding both volume buttons and plugging it in right ? (Should get a serial port). If that doesn't work it really is bricked. And you will need to jtag it. Link to comment Share on other sites More sharing options...
Guest Inf3cted Posted November 14, 2011 Report Share Posted November 14, 2011 When you say you have tried download mode. You mean with the battery removed - holding both volume buttons and plugging it in right ? (Should get a serial port). If that doesn't work it really is bricked. And you will need to jtag it. I have tryed that. Remove battery- holding both volume buttons and plugging it in. Nothing. But what is jtag and where i can do that? Link to comment Share on other sites More sharing options...
Guest unrandomsam Posted November 14, 2011 Report Share Posted November 14, 2011 You shouldn't expect anything just a serial port to appear in device manager. For jtag you need a device and you are probably better off with serial as well. Can you solder properly ? You need to solder at least 9 points to the pads on the board. And you need a jtag device and some software to use it that supports the right flash chip. Link to comment Share on other sites More sharing options...
Guest mastershifu Posted June 27, 2013 Report Share Posted June 27, 2013 You shouldn't expect anything just a serial port to appear in device manager. For jtag you need a device and you are probably better off with serial as well. Can you solder properly ? You need to solder at least 9 points to the pads on the board. And you need a jtag device and some software to use it that supports the right flash chip. Hey I am in need to revive my hard bricked ZTE blade via jtag. So i can solder, but i have no idea what that jtag device and software to use. Help me out. A little tutorial would be great too. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now