Jump to content

[How To]Save your dead vivacity!!


Recommended Posts

Guest iharrybao

firstly I want to say that I'm Chinese, and I have no idea if I could make you understand.

So let's begin!

1. you should download the stock ROM P736E, and extract it on your desk. Here's the B13 for you.

http://www.mediafire...b9d38933nmxwrp1

2.download the force flash tool (we call this, and I just translate it like that ) and extract it.

3.open the tool named USDL....

post-973697-0-14511100-1337490948.jpg

4.press the ! to change it to "管理员" mode.and input the code like this

post-973697-0-50577500-1337491046_thumb.post-973697-0-50268900-1337491057_thumb.

you can press the english verson if you are not chinese ;)

5.(on your phone)take out the battery. press the volume + and - at the same time.

you can press the volume keys with one of your thumb, and use another hand to conect your phone to your computer with USB. then the computer will find a hardware. check your device management, you'll find like this. just remember the COM you have!(mine is COM11)

post-973697-0-72987200-1337491361_thumb.

6.back to the tool, press option-port config

post-973697-0-15684900-1337491453_thumb.

7.choose the COM you have. better use line2.

post-973697-0-36089300-1337491504_thumb.

8.press the SW directory button to choose the B13 ROM(the on you have extract on your desk)

post-973697-0-59162400-1337491857_thumb.

9. press the button here

post-973697-0-36544900-1337491921.jpg

10.waiting!

after the download, your phone is alive~! :D

after that you can flash recovery and ROMs

Edited by iharrybao
Link to post
Share on other sites
  • 2 months later...
Guest Russ_uk

2.download the force flash tool (we call this, and I just translate it like that ) and extract it.

� 兴强刷工具.rar

Nice work iharrybao!

But the 'force flash tool' didn't download correctly for me (due to the Chinese characters), so I've changed it to English and re attached it here:

USDL_P726CV1.00.00.rar

Hope that helps.

Edited by Russ_uk
Link to post
Share on other sites
Guest Gligorije

hej ihar can u help me plz :) i have zte skate he was dead and i saw this tutorial done all steps but i did wrong and i used that blade2 stock rom instead of zte skate i finished all job but now phone gone crazy flash light on back blinking all time all buttons same... i cant get back to volume up and down and usb cable to see phone on Port ... how to i wipe again all and start from begining... nothing on phone not work just blinking like crazy.... help please ! :(

Sry for bad english :)

Link to post
Share on other sites
  • 3 weeks later...
  • 1 month later...
  • 1 month later...
  • 2 weeks later...
Guest ruyzalim

firstly I want to say that I'm Chinese, and I have no idea if I could make you understand.

So let's begin!

1. you should download the stock ROM P736E, and extract it on your desk. Here's the B13 for you.

http://www.mediafire...b9d38933nmxwrp1

2.download the force flash tool (we call this, and I just translate it like that ) and extract it.

3.open the tool named USDL....

post-973697-0-14511100-1337490948.jpg

4.press the ! to change it to "管理员" mode.and input the code like this

post-973697-0-50577500-1337491046_thumb.post-973697-0-50268900-1337491057_thumb.

you can press the english verson if you are not chinese ;)

5.(on your phone)take out the battery. press the volume + and - at the same time.

you can press the volume keys with one of your thumb, and use another hand to conect your phone to your computer with USB. then the computer will find a hardware. check your device management, you'll find like this. just remember the COM you have!(mine is COM11)

post-973697-0-72987200-1337491361_thumb.

6.back to the tool, press option-port config

post-973697-0-15684900-1337491453_thumb.

7.choose the COM you have. better use line2.

post-973697-0-36089300-1337491504_thumb.

8.press the SW directory button to choose the B13 ROM(the on you have extract on your desk)

post-973697-0-59162400-1337491857_thumb.

9. press the button here

post-973697-0-36544900-1337491921.jpg

10.waiting!

after the download, your phone is alive~! :D

after that you can flash recovery and ROMs

you saved my day i broked my phone and now its alive again many thanks ;)

Link to post
Share on other sites
  • 2 weeks later...
Guest ruyzalim

I keep gettign the error message "Partition.mbn is not exist"

Still have a bricked Crescent. Any advice?

did you extracted the rom to the desktop? and in the step 8 you choosed the folder of the extracted rom? if not , do so!

Edited by ruyzalim
Link to post
Share on other sites
  • 1 month later...
Guest s4sajii

Hello everyone:

I have tmoble vivacity. Restart on t-mobile logo.

Cant go into ftm or recovery mode with any combination key.

When i take battery out and press both vol up and vol down and insert usb cable. it vibrate and shows android logo and restart.

Anyone has any idea to put the the phone in to dfu mode to proceed with the above mention process.?

Thanks

Link to post
Share on other sites
Guest s4sajii

Hello everyone:

I have tmoble vivacity. Restart on t-mobile logo.

Cant go into ftm or recovery mode with any combination key.

When i take battery out and press both vol up and vol down and insert usb cable. it vibrate and shows android logo and restart.

Anyone has any idea to put the the phone in to dfu mode to proceed with the above mention process.?

Thanks

Hi,

I have open it. and observe that volume strip was broken. just join the missing link with the this wire and voila... phone was in FTM/DFU mode without problem. And is up and running in next 2 min. :) after flashing.

Best regards

Edited by s4sajii
Link to post
Share on other sites
  • 5 weeks later...
  • 1 month later...
Guest viti0ok

Prompt where to take please ROM for Orange SF2 and if probably describe please process with Orange SF2 it and there is zte crescent!!!

There will be very much блогдарен because you mine last hope!

I ask the application for my clumsy English :)

Link to post
Share on other sites
  • 1 month later...
Guest Jessica8

When I try to do the final step it says line 2 can't read the 'armprgZTE.bin' file :s

What should I do ? Help please. :(

Edited by Jessica8
Link to post
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
Guest TygerTyger

Thank you very much for this guide. I tried absolutely every technique, nothing worked, even ZTE's own recovery equivalent couldn't recognize the phone properly. But this worked and I have my phone back!

Link to post
Share on other sites
Guest channeler

firstly I want to say that I'm Chinese, and I have no idea if I could make you understand.

So let's begin!

1. you should download the stock ROM P736E, and extract it on your desk. Here's the B13 for you.

http://www.mediafire...b9d38933nmxwrp1

2.download the force flash tool (we call this, and I just translate it like that ) and extract it.

3.open the tool named USDL....

post-973697-0-14511100-1337490948.jpg

4.press the ! to change it to "管理员" mode.and input the code like this

post-973697-0-50577500-1337491046_thumb.post-973697-0-50268900-1337491057_thumb.

you can press the english verson if you are not chinese ;)

5.(on your phone)take out the battery. press the volume + and - at the same time.

you can press the volume keys with one of your thumb, and use another hand to conect your phone to your computer with USB. then the computer will find a hardware. check your device management, you'll find like this. just remember the COM you have!(mine is COM11)

post-973697-0-72987200-1337491361_thumb.

6.back to the tool, press option-port config

post-973697-0-15684900-1337491453_thumb.

7.choose the COM you have. better use line2.

post-973697-0-36089300-1337491504_thumb.

8.press the SW directory button to choose the B13 ROM(the on you have extract on your desk)

post-973697-0-59162400-1337491857_thumb.

9. press the button here

post-973697-0-36544900-1337491921.jpg

10.waiting!

after the download, your phone is alive~! :D

after that you can flash recovery and ROMs

Hi, My vivacity suddenly had problems with booting up and just sticks at the T-Mobile Logo so I wanted to try your procedure to see if I can get the phone going again. In your instructions you said that your COM is COM 11but in the example you give it says:

"ZTE Handset Diagnostic Interface COM 13"

So in the example would it be COM 13 to use or am I missing something? Sorry, I am an amateur at all this.

Paul

Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.