Jump to content

S3C6410 Overclocking Tool: Need Omnia II/Louvre Testers


Guest daskalos
 Share

Recommended Posts

Please, could you all buddies here post both clock settings for APLL and MPLL? I tried a lot of APLL settings leaving MPLL as is and none was stable...

Link to comment
Share on other sites

6.5.x

i actually can get APLL 517*2 = 1034

I too managed to overclock my phone past 1Ghz (was using APLL of 512 and FPUEnabler on). I though it would be stable after running at that speed for a few days.

However, when I started some games which uses OpenGL (like Experiment 13, Xtrakt and Tower Defense), it crashed. Even launching the games after a soft reset crashes the phone. Had to downclock to 950Mhz (APLL of 450) for it to work.

FYI, not all Samsung CPUs are created equal. Some are able to be overclocked higher than others.

Link to comment
Share on other sites

No, it only set frequency on the fly, you can close it after... its why there is a shortcut creator tool... Frequency is then reset to normal frequency on sleep (when your screen is set off)

MPLL = Main Frequency, APLL = ARM Frequency, but i dont suggest to change MPLL, lcd and usb could be based on this main frequency... (in fast there is a third PLL, the EPLL for devices, which could be based on MPLL)

Link to comment
Share on other sites

  • 2 weeks later...

ROM version seems to play a part in stability.

i've just flashed to TWU2's JE2 lite rom and now i get stable overclock at APLL 480 MPLL 388

tried S3clock but nothing happens .... and FPU enabler isn't stable at all ... hangs with phonebook when adding contact to a message.

so i'm just using GPI0fix to overclock using shortcuts .... pretty stable ... am able to send MMS

Link to comment
Share on other sites

Hi guys, have you already tried to increase the voltage to make it more stable? Probably you can get higher if you do this. Not sure though if this is possible with haret. (check the manual). Does it get really hot at 1 ghz? In android this should be far more easy I think. But I first want to finish the project, it would an enourmouss loss if I bricked my phone.

EDIT: I think what would be more wise is to leave the MPLL to a bit lower value (standard it is 266), if you overclock this one also the lcd driver etc get a higher clock (dangerous!) or youll have to change the dividers. But what you probably do want is to have a higher memspeed, what you can easier do (and probably less dangerous) is to adjust the mem settings (yes the same as in your old computer which you overclocked). CHeck out page 128 and chapter 4 from the s3c6410 manual rev12.

Warning: this is on your own risk, im only giving you hints how to accomplish what you want.

Edited by almar
Link to comment
Share on other sites

Is it yet possible to get the clocks to stay after locking and unlocking the phone? If yes, how? I tried the software earlier but it was too difficult to overclock manually every time the phone was used...

Link to comment
Share on other sites

i think i found 1 cause of instability ..... openGL drivers are not so stable .... when using SPB ... if openGL is enabled it's a bit unstable at any frequency above 900 i think .... sometimes hangs phone as well.

testing with openGL disabled @470 APLL ...... seems very stable now.

Link to comment
Share on other sites

  • 4 weeks later...

is there like a guide for this? or can anyone write it please? when i set the APLL in the GPIOgfx v1.2d to 420 the program freezes and i have to soft reset it...i m running shadow angels JF5 ROM WM 6.5.3.

Link to comment
Share on other sites

i think i found 1 cause of instability ..... openGL drivers are not so stable .... when using SPB ... if openGL is enabled it's a bit unstable at any frequency above 900 i think .... sometimes hangs phone as well.

testing with openGL disabled @470 APLL ...... seems very stable now.

did you try to send MMS yet?

Link to comment
Share on other sites

  • 3 weeks later...
  • 1 month later...
YES!!!!. I've tested! It's interesting!!!!!!!!!

WOW, GREAT

how I longed for 6.5.5! juz becoz of s3clock i need to stick to 6.5 for the past several months...

LONG GONE THE PAIN NOW~

Link to comment
Share on other sites

  • 1 month later...
Is it yet possible to get the clocks to stay after locking and unlocking the phone? If yes, how? I tried the software earlier but it was too difficult to overclock manually every time the phone was used...

did you find solution for this? ty

Link to comment
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
 Share


×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.