Jump to content

[KERNEL] SFR Staraddict kernels for "all" custom roms


Recommended Posts

This is the set of kernels suitable for SFR Staraddict devices

having touchscreen response issues on standard kernels shipped with custom ROMs.

These kernels are configured for ATMEL MXT224_P743F touchscreens.

However, it was reported that some SFR Staraddict models are using the same touchscreen as other Skate models

(Synaptics or Focaltech). So if this is your case then use kernels from this thread instead:

http://www.modaco.co...ll-custom-roms/

"Thanks" go to manufacturers for bringing such a chaos here...

Be sure you pick one from the correct category.

For CyanogenMod based ROMs two versions are available - normal and volume boosted that

can be used if you find volume levels too low (be aware of distortion @ high volume levels).

Use at your own risk.

Flash in clockworkmod - no wipes are needed.

Backup your ROM before flashing so you can easily restore your system in case of problems.

Changelogs

Changelog 06/03/2013

- S5 - updated for FM Radio compatibility needed by Android 4.2.2 ROMs

- S5 - compatible with ParanoidJelly2 and RootBox only!!!

- S4 - updated for FM Radio compatibility needed by Android 4.1.2 ROMs

- S4 - updated GPU driver

- S4 - compatible with ParanoidJelly1 (v2.70 and later)

Changelog 27/02/2013

Updated S5 kernel.

Massive thanks to daemond for porting updated KGSL kernel drivers.

Updated KGSL drivers. KGSL is the kernel part of the GPU driver, and the update fixes out of memory issues which usually resulted in white textures in games and demanding applications. It might also improve stability, there are loads of changes and many bugfixes in the new driver.

Changelog 03/02/2013

- S5 - kernel for ParanoidJelly2 and RootBox (Android 4.2.2)

- S5 - compatible with ParanoidJelly2 and RootBox only!!!

Changelog 25/01/2013

- S4 - added support for hardware VSYNC

- S4 - compatible with ParanoidJelly 2.63 (and later) only!!!

Changelog 10/01/2013

- S4 updated for compatibility with the ParanoidJelly CM10 (and possibly CFX3 CM10.1)

Changelog 15/12/2012

- CM9 S3 kernels updated for compatibility with the current PA ROM release

Changelog 16/11/2012

- ICS S3 kernels updated for compatibility with native wifi tethering that has been recently fixed in my ParanoidAndroid ICS ROM

Changelog 21/10/2012

- CPU Governors revised

--- fixed Lagfree not scaling below 480MHz

--- fixed conservative stuck at max. frequency

--- fixed SavagedZen not ramping higher than 480MHz

--- ondemand parameters changed to match those ZTE is using in stock ROMs

--- new governor: SmartassH3 - based on SmartassV2 with parameters tuned by H3ROS (thanks) -

more efficient frequency scaling - not ramping too high when not needed this could potentially

result in better battery life

- added compatibility hack for some newer TRULY replacement LCDs

- default governor set to SmartassH3 with default min. frequency 122MHz

Download links

S2 - Stock based custom ROMs (Atomic, H3 Blues, SKatie, ...)

http://tinyw.in/d3hR

S3 - CM7 Based ROMs (CM7.2, MokeeOS, IceArmor, ...)

Normal version: http://tinyw.in/pM3W

Volume boosted version: http://tinyw.in/MIZ7

S3 - CM9 Based ROMs (ColdfusionX, ICS ParanoidAndroid 1.6, ...)

Normal version: http://tinyw.in/TQkk

Volume boosted version: http://tinyw.in/aSSs

S4 - Compatible with ParanoidJelly 2.70 (Android 4.1.2)

http://tinyw.in/KOlS

S5 - Compatible with ParanoidJelly2, RootBox (Android 4.2.2)

http://tinyw.in/Hooj

Thanks got to 4471688 and Franck Black for helping me with testing.

Edited by C3C0
Link to post
Share on other sites
  • Replies 76
  • Created
  • Last Reply

Popular Posts

This is the set of kernels suitable for SFR Staraddict devices having touchscreen response issues on standard kernels shipped with custom ROMs. These kernels are configured for ATMEL MXT224_P743F to

Flashing the kernal over PA should do the trick. Pick SFR in case you have SFR otherwise pick the other one from "S series" kernel thread. http://www.modaco.com/topic/353434-kernel-s-series-kernel-f

SFR kernels for CM9 based roms now available in the first post. Thanks again to everybody who helped with testing.

Posted Images

Guest SingleWolf

Just updated wtih S3-CM9 "for all", have no any touchscreen issues (and with all previous "non-SFR" versions too). What's I need to test more accurate, or I simply have an "wrong" Staraddict :) ?

Link to post
Share on other sites

Probably your device has the same touchscreen as other non—sfr skates have :) Manufacturers are bringing chaos here. :) And the problem is that they released kernel sources just for very first models (September 2011)

Link to post
Share on other sites

How to Check which one I have and which kernel to use.

Or if you don't experience touchscreen response issues at edges or "mouse pointer" showing on ics roms or picture being off bottom edge then you have older skate model that majority here has and thus don't need to use this one but normal S series kernel.

Link to thread is in the first post.

Link to post
Share on other sites
Guest SingleWolf

C3C0

Is this kernel have only difference in touchscreen driver configuration from "for all" kernel? Strange, but I have no more battery leak by 2-5% per night after updating to it (same ROM, software, configuration and usage, no any wakelocks detected).

Link to post
Share on other sites
Guest Viento del Sur

Hi CECO:

What about ceco s2 rev1 (for skatie rom)?

In Skatie forum people say it improves the graphics quality, better color and brightness...

It is also compatible with OrangeMontecarlo of Spain?

regards.

Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.