Jump to content
dakok

[GUIDE] YGDP Tool for flashing stock 4.2 & 4.4 roms

Recommended Posts

so, finally managed to get YGDP to flash the ROM, is there a way I can only flash certain parts of the ROM rather than the whole ROM like SP Flash Tool ? Like only flash recovery, logo.img

Edited by Uchiha_1123

Share this post


Link to post
Share on other sites
On 10/2/2014 at 5:29 PM, krish_nank said:

Bro but i am hardcore fan of MIUI and tried Coolpad rom i lost IMEI could not restore it....

same here, please help

Share this post


Link to post
Share on other sites

so, finally managed to get YGDP to flash the ROM, is there a way I can only flash certain parts of the ROM rather than the whole ROM like SP Flash Tool ? Like only flash recovery, logo.img

you can try deleting the folders you dont need from the folder ygdp unpacks the cpb in your harddrive before it goes on with the installation.maybe it will flash only the files remaining,maybe it will fail,just try and see!

But:if your previous rom was not tha same with the cpb you are flashing,you may have conflicts.

Also:ygdp maybe formats the previous rom BEFORE installation.Thats very probable.Then maybe you will end up with a brick.Be careful!

Share this post


Link to post
Share on other sites

I cannot unbrick my phone with any tools..

In flash tool even if it procceed till the end,it cannot boot..When i go to recovery it's still at CWM 6.0.5..

With YGDP it stops at 98%..

00:56:47 CELL0: Software Version: Assembly - <V3.98_141222_02>

00:56:47 CELL0: Cell 0 USB address is: com8

00:56:47 CELL0: Start Download.

00:56:47 CELL0: Download Started...

00:56:47 CELL0: Downloading CPB:

00:56:47 CELL0: Init Connect Arg.

00:56:47 CELL0: Downlaod DA Start.

00:56:50 CELL0: Downlaod DA Success.

00:56:50 CELL0: Verify is Partition be Changed.

00:56:50 CELL0: Get Usb Status Success.

00:56:50 CELL0: Read YL-Parames Partition Start.

00:56:52 CELL0: Read YL-Parames Partition Success.

00:56:52 CELL0: Check between YL-Parames Partition and PhoneInfo Start.

00:56:52 CELL0: Check between YL-Parames Partition and PhoneInfo Success.

00:56:52 CELL0: Init BackUp Table.

00:56:52 CELL0: Read BackUp File Start.

00:57:42 CELL0: Read BackUp File Success.

00:57:42 CELL0: Mach Storage Type is Successful.

00:57:42 CELL0: startAddr 5f000000, format length 171b00000

00:57:45 CELL0: Format Device Success.

00:57:45 CELL0: Start Download CPB.

00:59:55 CELL0: Download CPB Failed.

00:59:55 CELL0: ERROR:1041

00:59:55 CELL0: DisConnect.

01:00:15 CELL0: Total download time elapsed: 3 min : 28 sec

01:00:15 CELL0: Downloading CPB: Failed!


This is how it is recognised at USBDeview:

MT65xx Preloader    MediaTek PreLoader USB VCOM Port  

 

When i get in recovery mode it writes the followings:

E:Can't mount/cache/recovery/command

E:Can't mount/cache/recovery/log

E:Can't open/cache/recovery/log

E:Can't mount/cache/recovery/last_log

E:Can't open/cache/recovery/last_log

E:Can't mount/cache/recovery/last_install

E:Can't open/cache/recovery/last_install

 

Any help on what may be wrong??

edit

I've tried this 2 rom posted by mixanikos:

http://download.yulong.com...0828856(2).rar

http://download.yulong.com...0844349(3).rar

YGDP.png

Edited by wiowia

Share this post


Link to post
Share on other sites
13 hours ago, wiowia said:

I cannot unbrick my phone with any tools..

In flash tool even if it procceed till the end,it cannot boot..When i go to recovery it's still at CWM 6.0.5..

With YGDP it stops at 98%..

00:59:55 CELL0: Download CPB Failed.

00:59:55 CELL0: ERROR:1041

00:59:55 CELL0: DisConnect.

01:00:15 CELL0: Total download time elapsed: 3 min : 28 sec

01:00:15 CELL0: Downloading CPB: Failed!


This is how it is recognised at USBDeview:

MT65xx Preloader    MediaTek PreLoader USB VCOM Port  

 

When i get in recovery mode it writes the followings:

E:Can't mount/cache/recovery/command

E:Can't mount/cache/recovery/log

E:Can't open/cache/recovery/log

E:Can't mount/cache/recovery/last_log

E:Can't open/cache/recovery/last_log

E:Can't mount/cache/recovery/last_install

E:Can't open/cache/recovery/last_install

 

Any help on what may be wrong??

edit

I've tried this 2 rom posted by mixanikos:

http://download.yulong.com...0828856(2).rar

http://download.yulong.com...0844349(3).rar

 

 

Which was your previous rom?

In spflash tools did you click format all + download ?

Can you flash the zip from your previous rom with cwm 6.0.5.0 ?

For unbrick use the first official 4.2 rom from here:

https://drive.google.com/folderview?id=0B4huyVgvdssGMXFTRFJ0QmNoUGc&usp=sharing#list

https://drive.google.com/folderview?id=0B4huyVgvdssGMUNQNElsQ2VaMHM&usp=sharing#list

 

I would also suggest to try the older version of YGDP tools, so you can select the model 8297W

I read "giorgos" in the screenshot. Are you Greek?

 

Share this post


Link to post
Share on other sites

In spFlash tool, check everything EXCEPT PRELOADER. 

 press the download button. 

That’s all

 

Edited by Jpower73

Share this post


Link to post
Share on other sites
2 hours ago, Jpower73 said:

In spFlash tool, check everything EXCEPT PRELOADER. 

 press the download button. 

That’s all

 

I did that too but it didn't work although it completes the task..

Flash_Tool.png

Share this post


Link to post
Share on other sites

Do the same operation but this time, do it keeping both volume up +down buttons pressed 

 

If Ok. 

Unplug it. 

Take off/on battery for few seconds. 

Boot. 

 

Edited by Jpower73

Share this post


Link to post
Share on other sites
5 hours ago, Jpower73 said:

Do the same operation but this time, do it keeping both volume up +down buttons pressed 

 

If Ok. 

Unplug it. 

Take off/on battery for few seconds. 

Boot. 

Nope...It's the same..

If it isn't the drivers then i suppose that it is done..

Edited by wiowia

Share this post


Link to post
Share on other sites
1 hour ago, NunoCruz said:

Hi, any one know where I can get a stock rom for coolpad 8860U also know as vodafone smart 4g?

Any use? 

Use Google/Chrome translate.

https://www.androidpt.com/topic/57647-tutorial-vodafone-smart-4-turbo-kitkat/

Edit: oh - scratch that - wrong model I think.

I got that link here in case it helps at all:

https://www.androidpt.com/topic/58150-vodafone-smart-4g-coolpad-8860u-ota-updates-servidor-testes-yulongcoolpad/

Edited by dalyer

Share this post


Link to post
Share on other sites

can you upload the .cpm file somewhere? can't find any other way to download from baidu :/ can't register with my number, says invalid :/

my device is Coolpad Note 3 8676-I02 MT6753, I did flashing using SP tool using this firmware file https://drive.google.com/file/d/0B66ezAqMul7QUzZFWlNBdVA2Y0E/view

the phone IMEI is unknown and I tried the using imei.exe command but now the IMEI is showing differently(see photo)!

Serial number is also different in the phone and different in the box :/

please help me get out of this!

IMG_1911.JPG

Edited by Dheeraj R
serial number issue

Share this post


Link to post
Share on other sites

Hello. I'm cought up in a terrible loop and I hope someone can help. I have a Coolpad Modena E501 it was on lollipop. I rooted it with kingroot and wanted to instal twrp with Rashr. It asked me to reboot to recovery i pressed yes, the phone turned off and screen popped up to press volume up to proceed or vol down to cancel, however the buttons are not responding. I tried connecting it to pc and pressing vol up then I get a message "Information, do not unplug cable from your computer." and that's it it's stuck on that. I downloaded stock rom and tried with ygdp tool to flash it but I can't find the assembly number of my phone. I also tried with newer version but i get code 0 downloading failed. Any suggestions? I'd really appreciate it, thank you very much.

 

Edit: I can't take the battery out because it's built in. I installed drivers that came with stock rom zip but I pressume that pc is not recognizing it. When it's plugged to pc with information message, pc recognizes it like "android coolpad bootloader". Something like that, if you guys need screenshots or dump files let me know.

Edited by brchina

Share this post


Link to post
Share on other sites

Can anyone help - I am also stuck on the 98% failure for the Coolpad F1?

 I have tried 4 different versions of YGDP and 2 versions of the CPB files (4.4.035 & 4.4.046). Some of the versions will work and others are just getting hung at the 'Entering Download' stage - I have also disabled anti-virus on the PC when attempting these)

I was running the (rooted) ROM AOSP-Nitro-A310-V3-Repack with CWM installed (This is no longer loading after various re-flashing attempts to un-brick the phone) and had the could not mount \cache error.

Is there a site to download any later CPB files, as I was not able to from the the Baidu site, or anything else I can try, as I can only get as far as the Google boot logo?

I have also tried SP Flash Tools and can get as far as the Download DA red bar loading, and then get the error 'BROM Error : S_BROM_CMD_JUMP_DA_FAIL (0x7F3)'

Thanks in advance!

 

EDIT - Log files attached, but the main errors are:

 

20:51:51  CELL0:  Fail to transmit boot.img file Flag code

20:51:51  CELL0: Res:

Checksum Error.

20:51:51  CELL0: Download failed,please try again!!

20:51:51  CELL0: Total download time elapsed: 4 min : 21 sec

20:51:51  CELL0: Downloading all files: Failed!

 

 

8297W_FAILED_CELL0_20.51.51.rtf

Edited by nsmacd1

Share this post


Link to post
Share on other sites
5 hours ago, rista1 said:

Still failing at 98% unfortunately with this & other versions of the YGDP tool, but thanks anyway!

https://drive.google.com/file/d/0B21y7GJ5u_6cX1M5aDJrNG9wUFU/view?usp=drivesdk

https://drive.google.com/file/d/0B21y7GJ5u_6ceDNNYnBldlhRNHc/view?usp=drivesdk pass 369

 

Edited by nsmacd1

Share this post


Link to post
Share on other sites

Hi Dakok.

Thanks for the tip, but I tried the CDA tool first (Version V1.89_141231), but could not get it to go which is why I am trying the YGDP tool.

I tried CDA again with CPB file 4.4.046.P0.150720.8297W.CPB and this too fails at 98% with the error screen attached, if you have any idea what this says? :-)

The phone display says Writing Flash.....' followed by 'Checksum error'

What do you reckon - Wrong CPB file, or phone is fried?

 

I have also tried with these CPB files, all with the same result: (The label behind the battery says Coolpad 8297 W, so I guess I have the correct CPB files).

4.2.020.P0.140409.8297W.CPB

4.4.035.P0.150323.8297W.CPB

4.4.046.P0.150720.8297W.CPB

I also tried with/without memory card and battery installed and with anti-virus turned off, if you have any other ideas?

Thanks again!

 

Capture.JPG

Edited by nsmacd1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.