Jump to content

Coolpad F1 8297w - Review / Info / Software / Custom Roms


Guest dakok

Recommended Posts

Guest Jpower73

Does this one have the recurring update supersu notification "issue"?

Most of Liutao's roms do

Yes, on every reboot.

Edited by Jpower73
Link to comment
Share on other sites

Guest 77chedu

Yes, on every reboot.

Ok, That's because of the way supersu is installed. 

 

Having that much acceptance over the greek forum, hopefully someone can take a look in to that (updater script)

Link to comment
Share on other sites

Guest Jpower73

Ok, That's because of the way supersu is installed.

Having that much acceptance over the greek forum, hopefully someone can take a look in to that (updater script)

I think the solution is to uninstall it and re flash the newest version.

Link to comment
Share on other sites

Guest Jpower73

Screenshot_2015-01-16-20-33-23_zpsvaf4ui

WOW..
Interpolarated ram storage too..
;)
S5 rom

edit:

Also,

if you encounter high energy draining, i think i found the solution..

Using wakelock detector i noticed that there's  a service called "server system 1.0" which was hitting with an average of 1 interrupt every 0.6 sec.

Searching SGS5 forums i found out that the following services it is safe to get "frozzen".

After that Δ was decreased from 11% to 6.5%/h with  more than an hour SOT.

Screenshot_2015-01-16-21-13-39_zpsi94pxw

+ "Factory Mode 1.0" + "Hub 1.0" services

+ smart remote apk

(this could help http://forum.xda-developers.com/showthread.php?t=1752668)

NOTICE/WARNING: ALWAYS KEEP A NANDROID BACKUP, IN CASE SOMETHING GOES WRONG.

btw,

 

another camera sample, same conditions, without flashlight, incandescent enviroment lightning using a better camera, S5 rom

set at 13,4mp (16:9)
https://www.dropbox.com/s/...05326.jpg?dl=0
3.9MB file size

set at 21,6mp (16:9)
https://www.dropbox.com/sc...IuEYrgzI5RDLJa
6.1MB file size

 

I  :wub: interpolaration

:D

Edited by Jpower73
Link to comment
Share on other sites

Jpower73,

Please post output from 'free' command from terminal emulator on this rom.

I suppose that it could have 'zram' + swap in ram configured that may show more memory because of realtime memory compression, but I haven't checked this rom yet.

Link to comment
Share on other sites

Guest Jpower73

Jpower73,

Please post output from 'free' command from terminal emulator on this rom.

I suppose that it could have 'zram' + swap in ram configured that may show more memory because of realtime memory compression, but I haven't checked this rom yet.

here U R

Screenshot_2015-01-16-22-26-40_zps2i2jlv

 

Screenshot_2015-01-16-22-29-38_zpswltweo

Edited by Jpower73
Link to comment
Share on other sites

 

Using wakelock detector i noticed that there's  a service called "server system 1.0" which was hitting with an average of 1 interrupt every 0.6 sec.

+ "Factory Mode 1.0" + "Hub 1.0" services

+ smart remote apk

 

Wonder if any of those are more malware like the Coolpad and Micromax ones....? :|

Link to comment
Share on other sites

Jpower73,

Thanks. As I thought, if you didn't setup swap partition on sdcard then it has to be swap in zram.

You can confirm that if you get /dev/zram0 device in output of 'cat /proc/swaps'.

Generally on multicore CPUs such realtime RAM compression doesn't impact performance, is really useful and makes impression like device had a lot more RAM - when I did zram testing on few other devices I got ratio of 3:1-3.7:1 (on my laptop this way I really use up to 24-25GB RAM on physical 8GB) so in this case it means that you are able to use up to 4-5GB of RAM even if it show around 3GB.

The other good approach of that is that memory is not being compressed until most of it is used, then it starts compression of things that don't fit these not compressed 2GB.

This makes a lot better results than swap on sdcard or using simply our 2GB without compression.

I did such tests on F1 on AOSP 4.4.2 sometime before as kernel on both 4.2.2 & 4.4.2 supports zram - it just needed to script such device creation at desired size, making swap on it & enabling it at boot.

And Lenovo A850+ for example has it enabled in stock fw to make better use of it's only 1GB RAM (no real difference this way with 2GB RAM use in F1).

Edited by xeros2
Link to comment
Share on other sites

Guest bore1989

any link for gapps for this rom ? please :)

I too would appreciate the link for working gapps... I tried with gapps-jb-20130812-signed and it would crash during setup..

Link to comment
Share on other sites

Guest mixanikosgr

Wonder if any of those are more malware like the Coolpad and Micromax ones....? :|

2 of them are from the same company ADUPS found in the Micromax rom.

BUT i checked 1-2 other roms zips and i found them there also

Link to comment
Share on other sites

Guest Dreamkill3r

Actually a user from 4pda (serg1406) shared a working miui 6 https://yadi.sk/d/r7Xrqp3Me33mn
a problem was with gapps and root,but some people have found the proper packages
everything flash throught recovery/twrp
root gapps
maybe you can find small buggs,but in general,the rom is working)

Edited by Dreamkill3r
Link to comment
Share on other sites

Guest m@nish123

Actually a user from 4pda (serg1406) shared a working miui 6 https://yadi.sk/d/r7Xrqp3Me33mn

a problem was with gapps and root,but some people have found the proper packages

everything flash throught recovery/twrp

root gapps

maybe you can find small buggs,but in general,the rom is working)

r u sure it is working ??? no network problem or sound bug ??
Link to comment
Share on other sites

Guest m@nish123

Which sound bug?

Network is working,but I dont know about a sound bug

Btw,vibration is not working also

sound etc i got from ydss i think wrong translation

can u please post more ss like recent app,status bar and settings

Link to comment
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.