Guest chil360 Posted November 18, 2015 Report Posted November 18, 2015 (edited) CyanogenMod 13 Unofficial builds for Huawei Y300/G510/G330 Disclaimer: CyanogenMod and I are not responsible for any damages to your device. Download: Basketbuild - https://basketbuild.com/devs/chil360 GApps: I would recommend Opengapps (ARM/6.0) Pico but any GApps for Masrhmallow should work. Using GApps slows the phone considerably so I would advise using minimal GApps editions. With Opengapps, it must be installed at the same time as the rom. Installing at a later time causes FC's when the phone is rebooted. Note: To fix AOSP keyboard with opengapps pico remove the file: /system/lib/libjni_latinimegoogle.so Current Status: Working so far: It boots successfully, display works, touchscreen & buttons all work ok GPS Wifi Bluetooth Audio Video playback (software decoding) Internal & External SD Card - Internal set as primary storage, External is adoptable. Phone/Data - Needs testing! Rild & libril now built from source using custom libril based on CM13 hardware/ril-caf with a commit from LegacyHuawei. Camera Not Working: Video playback (hardware decoding) FM Radio Comments/Known Issues: Wifi: When configuring wifi during the setup wizard, wifi connects to the access point but sometimes doesn't make an internet connection. Skip through the setup wizard, go to Settings -> Wifi, turn off wifi, turn it back on and it will connect successfully. Mobile Data: If mobile does not connect when enabled, turn on aeroplane mode, wait a few seconds then turn off aeroplane mode. When the phone reconnects to the network it should also successfully connect the mobile data. Now that the initial connection has been made, you should be able to disable and enable mobile data as required and it will connect. Sources: CyanogenMod - http://github.com/CyanogenMod Device Tree - https://github.com/CM13-Y300 Kernel - https://github.com/SlimLP-Y300/chil360-kernel/tree/mm6.0 Credits: CyanogenMod Dazzozo TeamHackLG Christopher83 moddingg33k mrg666 srfarias fonz93 ... and many more contributors! Edited December 18, 2016 by chil360
Guest chil360 Posted November 18, 2015 Report Posted November 18, 2015 (edited) Changelog: 18/12/2016 Updated CM13 sources to 18/12/2016 11/12/2016 Updated CM13 sources to 11/12/2016 04/12/2016 Updated CM13 sources to 04/12/2016 27/11/2016 Updated CM13 sources to 27/11/2016 20/11/2016 Updated CM13 sources to 20/11/2016 13/11/2016 Updated CM13 sources to 13/11/2016 06/11/2016 Updated CM13 sources to 06/11/2016 30/10/2016 Updated CM13 sources to 30/10/2016 23/10/2016 Updated CM13 sources to 23/10/2016 16/10/2016 Updated CM13 sources to 16/10/2016 09/10/2016 Updated CM13 sources to 09/10/2016 02/10/2016 Updated CM13 sources to 02/10/2016 25/09/2016 Updated CM13 sources to 25/09/2016 18/09/2016 - Basketbuild is up again! Updated CM13 sources to 18/09/2016 11/09/2016 - Download from Mega here: https://mega.nz#F!yFNFCTrK!tS8_Az5zhsAXz4jeamngJg!TclFESjT Updated CM13 sources to 11/09/2016 04/09/2016 - Download from Mega here: https://mega.nz#F!yFNFCTrK!tS8_Az5zhsAXz4jeamngJg!TclFESjT (as Basketbuild is still down!) Updated CM13 sources to 04/09/2016 28/08/2016 - Download from Mega here: https://mega.nz#F!yFNFCTrK!tS8_Az5zhsAXz4jeamngJg!TclFESjT (as Basketbuild is currently down) Updated CM13 sources to 28/08/2016 21/08/2016 Updated CM13 sources to 21/08/2016 14/08/2016 Updated CM13 sources to 14/08/2016 07/08/2016 Updated CM13 sources to 07/08/2016 31/07/2016 Updated CM13 sources to 31/07/2016 24/07/2016 Updated CM13 sources to 24/07/2016 17/07/2016 Updated CM13 sources to 17/07/2016 Try BenzoSM 4.9 toolchains (see here) 10/07/2016 Updated CM13 sources to 10/07/2016 03/07/2016 Updated CM13 sources to 03/07/2016 Add Wifi patches from Oleg S. (remittor) for increased wifi stability Wifi: Disable IpReachability monitor Kernel: Add 3 display commits by Oleg S. (remittor) 26/06/2016 Updated CM13 sources to 26/06/2016 Switchable Internal/External SD as Primary storage (see here) 19/06/2016 Updated CM13 sources to 19/06/2016 12/06/2016 Updated CM13 sources to 12/06/2016 05/06/2016 Updated CM13 sources to 05/06/2016 29/05/2016 Updated CM13 sources to 29/05/2016 22/05/2016 Updated CM13 sources to 22/05/2016 15/05/2016 Updated CM13 sources to 15/05/2016 08/05/2016 Updated CM13 sources to 08/05/2016 01/05/2016 Updated CM13 sources to 01/05/2016 24/04/2016 Updated CM13 sources to 24/04/2016 patch: build - Remove android.hardware.ethernet.xml permission from Emulator.mk. This fixes the initial connection of wifi during the Setup Wizard (Connected, no Internet). As our wifi uses the device name 'eth0' (instead of wlan0) this permission must somehow be causing a conflict. 17/04/2016 Updated CM13 sources to 17/04/2016 Wifi: Remove custom wifi.c - Our custom wifi.c hasn't been updated since kitkat so is out of date compared to the stock wifi.c (from libhardware_legacy). The stock version seems to work without any modifications required for our wifi hardware in CM13. 10/04/2016 Updated CM13 sources to 10/04/2016 Kernel: pipe: Fix buffer offset after partially failed read UPSTREAM: include/linux/poison.h: fix LIST_POISON{1,2} offset msm: ipc_router: Bind only a client port as control port net/ipv6/route.c: packets originating on device match lo 03/04/2016 Updated CM13 sources to 03/04/2016 27/03/2016 Updated CM13 sources to 27/03/2016 20/03/2016 Updated CM13 sources to 20/03/2016 Build toybox from source again - kernel updated to support finit_module so wifi module are loading correctly now. Add legacy audio policy hal to device tree as it has been removed from core CM codebase. Kernel: Enable CONFIG_SECCOMP Add a number of commits to update seccomp Add finit_module support (requires seccomp) 13/03/2016 Updated CM13 sources to 13/03/2016 Replace deprecated wifi supplicant scan interval property with new overlay setting. This should hopefully fix the constant wifi disconnect/re-connect in last weeks build. Fix auto-rotate issue. Use prebuilt toybox binary as current toybox sources cause a failure to properly load the kernel wifi modules. 06/03/2016 Updated CM13 sources to 06/03/2016 28/02/2016 Updated CM13 sources to 28/02/2016 21/02/2016 Updated CM13 sources to 21/02/2016 14/02/2016 Updated CM13 sources to 14/02/2016 Kernel: neigh: Better handling of transition to NUD_PROBE state (Fixes Wifi dropouts!) 07/02/2016 Updated CM13 sources to 07/02/2016 Kernel: Increase camera heap size 31/01/2016 Updated CM13 sources to 31/01/2016 Enabled Snap camera app 24/01/2016 Updated CM13 sources to 24/01/2016 17/01/2016 Updated CM13 sources to 17/01/2016 10/01/2016 Updated CM13 sources to 10/01/2016- Android 6.0.1_r10 03/01/2016 Happy New Year! Updated CM13 sources to 03/01/2016 Cherry-pick Browser runtime permissions commit - fixes browser FC when trying to download 27/12/2015 Updated CM13 sources to 27/12/2015 20/12/2015 Updated CM13 sources to 20/12/2015 13/12/2015 Updated CM13 sources to 13/12/2015 - Android 6.0.1_r3 Kernel now built with UBERTC 4.9 toolchain Replace CMUpdater with my own update checker - OTAUpdater (based on SlimOTA) - with direct download of latest rom from Basketbuild Launch from Settings -> About Phone -> CyanogenMod Updates 06/12/2015 Updated CM13 sources to 06/12/2015 Device updates - Tune KSM config to reduce cpu usage which improves battery usage and performance. 29/11/2015 Updated CM13 sources to 29/11/2015 Initial build for G330 Device updates - cleanups & performance tweaks. 23/11/2015 Initial build for G510 Add support for the Internal SD storage and set as primary. External SD is now configured as adoptable. Revert to KSM (instead of UltraKSM) and change the default I/O scheduler back to deadline (from bfq) - this improves battery life. Device updates to help performance. 18/11/2015 Initial build for Y300 Edited December 18, 2016 by chil360
Guest Mr Voland Posted November 18, 2015 Report Posted November 18, 2015 (edited) @chil360Nice one, will test it.So as I understand you we can't use use internal storage at all?I havent sd card in phone so that means that I can't use phone normally?Which gapps we should use? Edited November 18, 2015 by Mr Voland
Guest chil360 Posted November 18, 2015 Report Posted November 18, 2015 (edited) If there's no External SD card it should fall back to emulating primary storage in /data.I have tested with OpenGapps ARM/6.0 which works ok. I use the smallest possible gapps (pico) as gapps slows the rom considerably. Edited November 18, 2015 by chil360
Guest Mr Voland Posted November 18, 2015 Report Posted November 18, 2015 (edited) Mistake, delete post please.. Edited November 18, 2015 by Mr Voland
Guest chil360 Posted November 18, 2015 Report Posted November 18, 2015 Work in G510?Y300 roms usually work ok on G510 as there is very little difference between the two devices. A few things may not work and it will identify the device as a Y300 but nothing major.
Guest luca020400 Posted November 18, 2015 Report Posted November 18, 2015 (edited) Pls trash your y300 Great work as always Anyway there is a patch on gerrit allowing internal sd card to be used as main storage ( android_system_vold ) Edited November 18, 2015 by luca020400
Guest dixmer Posted November 18, 2015 Report Posted November 18, 2015 So you see in this fix if hardware acceleration ?
Guest chil360 Posted November 18, 2015 Report Posted November 18, 2015 Pls trash your y300 Great work as always Anyway there is a patch on gerrit allowing internal sd card to be used as main storage ( android_system_vold )Thanks luca, I will experiment with that patch tomorrow. So you see in this fix if hardware acceleration ?Hardware video acceleration relies on proprietary OMX libraries which were built for Jellybean. With all of the changes in newer android releases and having to move to display-caf for LP/M it is highly unlikely that hardware acceleration could ever be made to work.
Guest Mr Voland Posted November 18, 2015 Report Posted November 18, 2015 (edited) Used it for short time (without gapps) and: Camera don't work (and gallery ofc), browser don't work, and also file manager.Beside that rom is smooth, and there isn't blackscreen, or at last didn't experienced it, call deley is reducet it rings after one 'beep'.So i've returned to fluffy rom and there in total commander has been showed like I have external sd, and I couldn,t use rom at all, than instaled kra1o cm10.1, and i had problem with download, wifi or write speed so the file of 160mb was downloading for hour and half, and it wasn't up to my internet nobody else was connected and on pc internet worked as always.. So my advice is to not try installing rom before some updates, because it can broke some things...Anyway thanks to chil360 for his work, and I hope this rom will became stable .. Edited November 19, 2015 by Mr Voland
Guest dixmer Posted November 19, 2015 Report Posted November 19, 2015 Thanks luca, I will experiment with that patch tomorrow. Hardware video acceleration relies on proprietary OMX libraries which were built for Jellybean. With all of the changes in newer android releases and having to move to display-caf for LP/M it is highly unlikely that hardware acceleration could ever be made to work.ok thanks for answering .this rom fly is more fluid and will not see much lag
Guest pesartom Posted November 19, 2015 Report Posted November 19, 2015 Used it for short time (without gapps) and: Camera don't work (and gallery ofc), browser don't work, and also file manager.Beside that rom is smooth, and there isn't blackscreen, or at last didn't experienced it, call deley is reducet it rings after one 'beep'.So i've returned to fluffy rom and there in total commander has been showed like I have external sd, and I couldn,t use rom at all, than instaled kra1o cm10.1, and i had problem with download, wifi or write speed so the file of 160mb was downloading for hour and half, and it wasn't up to my internet nobody else was connected and on pc internet worked as always.. So my advice is to not try installing rom before some updates, because it can broke some things...Anyway thanks to chil360 for his work, and I hope this rom will became stable ..do you mean after a clean install of other roms, you had problems with them that you hadn't before?
Guest Trapezio Posted November 19, 2015 Report Posted November 19, 2015 Very nice!PS: why you hate the FM radio?
Guest Phoenix_510 Posted November 19, 2015 Report Posted November 19, 2015 Waiting for having it on my G510 ^_^
Guest dixmer Posted November 19, 2015 Report Posted November 19, 2015 This rom work very very good. Wait build g510
Guest Mr Voland Posted November 19, 2015 Report Posted November 19, 2015 do you mean after a clean install of other roms, you had problems with them that you hadn't before?Yeah, but after wiping everything multiple times, and installing 4-5 roms now is everything okey I guess, except on fluffy it won't work idk why.
Guest hgoldy300 Posted November 19, 2015 Report Posted November 19, 2015 Great work chil360![emoji106]
Guest seluce Posted November 20, 2015 Report Posted November 20, 2015 wow, seems nice!can someone test the new rom and tell something about the requirements and the feeling? How much RAM and CPU usage takes the rom vs KK/ LP?i guess KK is the best one for the old device (best optimized) but i can't test this rom now. status about this rom please asap :D
Guest cachetesmata3 Posted November 20, 2015 Report Posted November 20, 2015 That such friends he left have acquired another mobile ... It was a pleasure to be with you.
Guest Intel_sk Posted November 20, 2015 Report Posted November 20, 2015 (edited) huraaaaaaaaaa Edited January 10, 2016 by Intel_sk
Guest dre90210 Posted November 20, 2015 Report Posted November 20, 2015 Installed rom and things were ok...then installed opengapps 6.0 pico and everything crashing when reach setup
Guest chil360 Posted November 20, 2015 Report Posted November 20, 2015 Installed rom and things were ok...then installed opengapps 6.0 pico and everything crashing when reach setupYou need to install opengapps at the same time as the rom or it crashes as you have found.Reboot to recovery and do a factory reset then install opengapps and reboot.
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now